Abstract This study evaluated surface roughness, color stability, whitening index, and opacity of different types of modeling liquids for resin composite coating after exposure to staining and toothbrushing. Disc-shaped resin composite (Vittra APS, FGM) specimens were fabricated and divided into four groups (n = 10 each): control group, Composite Wetting resin (Ultradent Products), Adper Scotchbond Multipurpose adhesive (3M ESPE), and Adper Universal adhesive (3M ESPE). Surface roughness (Ra) was measured using a rugosimeter, while color stability (∆E00), whitening index (WI), and opacity (%) were measured using a spectrophotometer. Assessments were made at four time points: after polishing (baseline, T1), after immersion in red wine for 24 h (T2), and after 5,000 (T3) and 10,000 (T4) cycles of toothbrushing. Scanning electron microscopy images were captured to analyze the scratches created. The data were statistically analyzed by two-way repeated-measures analysis of variance and Tukey’s honestly significant difference tests (α = .05). Modeling with the Wetting resin resulted in higher surface roughness (p < 0.05) and low color stability, which were attributable to porosities. Higher color change values were observed in the control group after staining. Both adhesives showed the lowest mean ΔE00 values (p < 0.005). WI decreased after staining, except with the use of the Universal adhesive (p < 0.005). The lowest opacity values were observed at baseline for all groups (p < 0.005). The Universal and Scotchbond adhesives had lower surface roughness, better color stability, higher WI, and the lowest opacity values after staining with red wine and toothbrushing. toothbrushing Discshaped Disc shaped Vittra APS FGM n 1 each each) Ultradent Products, Products , Products) 3M M ESPE, ESPE ESPE) ESPE. . Ra (Ra rugosimeter ∆E00, E00 E ∆E00 (∆E00) (WI) % (% spectrophotometer points baseline, (baseline T1, T1 T T1) 2 T2, T2 (T2) 5000 5 000 5,00 T3 (T3 10000 10,00 T4 (T4 created twoway two way repeatedmeasures repeated measures Tukeys Tukey s α .05. 05 .05 .05) p 0.05 005 0 porosities ΔE ΔE0 0.005. 0005 0.005 0.005) E0 ∆E0 (∆E00 (WI ( (T2 500 00 5,0 (T 1000 10,0 .0 0.0 0.00 ∆E (∆E0 50 5, 100 10, 0. (∆E

Resumo Este estudo investigou os efeitos da inibição de oxigênio e dos procedimentos de acabamento/polimento nas propriedades das resinas compostas. Foram avaliadas uma resina composta bulk fill e duas resinas convencionais (nanoparticulada e microhíbrida). Os espécimes foram confeccionados, variando o tratamento de superfície: controle, sem tratamento; glicerina (inibidor de oxigênio); acabamento e polimento; glicerina + acabamento e polimento. O grau de conversão (GC) foi medido pela Espectroscopia de Infravermelho Transformada de Fourier (FTIR) imediatamente e após 15 dias da confecção dos espécimes (n=5). Os índices de alteração de cor ΔEab, ΔE00 e opacidade foram avaliados por meio de espectrofotômetro, após 15 dias de imersão no café, utilizando o sistema CIELAB (n=5). Os dados da alteração da cor foram analisados pelos testes ANOVA de dois fatores e Tukey (α=0,05) e a opacidade por ANOVA de medidas repetidas. O uso de glicerina aumentou significativamente o GC, no entanto, não teve influência sobre os valores ΔEab e ΔE00. O acabamento e o polimento reduziram os valores de ΔEab e ΔE00, independentemente da resina composta. A resina microhíbrida apresentou maior opacidade, seguida pela nanoparticula e bulk-fill, independentemente do tratamento de superfície. O acabamento e polimento resultou em menor grau de conversão das resinas compostas se comparado ao uso de um agente inibidor de oxigênio (glicerina), porém apresenta resultados similares para a pigmentação pelo café.

Abstract This study investigated the effects of oxygen inhibition and finishing/polishing procedures on the composite resin properties. One bulk-fill and two conventional composite resins (nanoparticle and microhybrid) were evaluated. Specimens were prepared using 4 surface treatments: control, no treatment; Gly, oxygen inhibition with glycerin; FP, finishing and polishing; Gly + FP, glycerin followed by finishing and polishing. The degree of conversion (DC) was measured using Fourier Transformed Infrared Spectroscopy (FTIR) immediately and after 15 days (n=5). Color stability (ΔEab, and ΔE00) and opacity were evaluated using a spectrophotometer after 15 days of immersion in coffee, using the CIELAB system (n=5). Data were analyzed by two-way ANOVA and Tukey tests (α=0.05) and opacity by two-way repeated-measures ANOVA. Glycerin usage increased significantly the DC however had no influence on the ΔEab, ΔE00 and, opacity values. Finishing and polishing reduced ΔEab and ΔE00 values, regardless of composite resins. Microhybrid showed higher opacity, followed by the nanoparticle and bulk fill, regardless of surface treatment. Post-polymerization polishing procedures resulted in lower conversion than using an oxygen inhibitor agent (Gly condition), but similar staining caused by coffee.

Abstract: This study aimed to assess the survival of glass ionomer cement (GIC) restorations performed using the atraumatic restorative treatment (ART) in elderly patients. The systematic review protocol was registered in the PROSPERO database. The records were searched until August 2020 in eight electronic bibliographic databases, and included randomized and non-randomized clinical trials and observational studies, with no restrictions on the language or year of publication. Study selection and data extraction were performed independently by two reviewers. Data were extracted, summarized, collected for qualitative analysis, and evaluated for individual risk of bias using the Joanna Briggs Institute's Critical Appraisal Tool. The literature search retrieved 5,186 records; however, only seven studies fulfilled the eligibility criteria and were included. The studies were published between 2002 and 2019. A total of 1,239 restorations were investigated at intervals of 6, 12, 24, and 60 months of follow-up. Some studies had a low risk of bias, while others had moderate and high risk of bias. In general, GIC restorations placed using ART were considered satisfactory. The 6-month, 12-month, and 24-month survival rates ranged from 81.3% to 97.2%, 72.2% to 94%, and 63% to 87%, respectively; additionally, the survival rate for the longest follow-up period (60 months) was 85%. Given the best evidence-based information regarding caries removal, we highlight the need to provide a conservative and effective technique for use in elderly patients. ART is a promising and viable alternative that guarantees the survival of restorations in elderly patients.

Abstract The aim of this study was to investigate the influence of preheating and post-curing methods on diametral tensile strength (DTS), flexural strength (FS), knoop microhardness (KHN), and degree of conversion (DC) of an experimental fiber-reinforced composite (FRC). Specimens (30 wt% of 3-mm-short E-glass fiber, 22.5 wt% of methacrylated-based resin and 47.5 wt% of filler particles) were subjected to: P – photocuring at 1500 mW/cm2 for 40 s (control); P/M – photocuring and microwave post-curing (540W/5 minutes); P/A – photocuring and autoclave post-curing (120°C/15 minutes); PH-P – preheating (60°C) and photocuring; PH-P/M – preheating, photocuring and microwave post-curing; and PH-P/A – preheating, photocuring and autoclave post-curing. Specimens for DTS (Ø 3 x 6 mm) and FS (25 x 2 x 2 mm) were tested at Instron 5965. KHN employed a 50g load for 30s. DC was measured using FTIR spectroscopy. Statistical analysis employed: factorial analysis, normality test, one-way ANOVA and Tukey’s HSD test, independent T-test and the Dunnett test. Interaction between factors was not significant (P>0.05). Preheating promoted significantly higher values of FS and KHN (p = 0.0001). Post-curing promoted significantly higher values for KHN (p = 0.0001). For DTS (p = 0.066) and DC (p= 0.724) no statistical difference was found between groups. SEM images showed that preheating promoted better interaction between glass fibers and resin matrix. Preheating increased FS, KHN and DTS, and post-curing increased KHN. DC was not affected by both methods. Preheating and post-curing methods can be used to improve some mechanical properties of FRCs’ but degree of conversion remains unaffected.

Apesar das diversas vantagens associadas aos pinos de fibra de vidro pré-fabricados, o corte da sua porção coronária deve ser realizado para permitir seu uso em algumas situações clínicas. Entretanto, o corte do pino cimentado pode gerar tensões na interface adesiva e afetar a resistência de união. O objetivo deste estudo foi avaliar o efeito do momento do corte do pino na resistência de união ao canal radicular. Sessenta raízes de incisivos bovinos foram incluídas em cilindros de resina com simulação do ligamento periodontal. Pinos de fibra de vidro foram cimentados utilizando um cimento resinoso convencional RelyX ARC (3M ESPE) ou autoadesivo RelyX Unicem (3M ESPE). Os pinos foram cortados previamente à cimentação, imediatamente após a cimentação, ou após a reconstrução do núcleo de preenchimento (n=10). Após o armazenamento por 24 h, as amostras foram seccionadas e submetidas ao ensaio de cisalhamento por extrusão utilizando máquina de ensaio mecânico (EMIC DL 2000). Os dados foram analisados por ANOVA dois fatores (cimento resinoso x momento do corte do pino) e teste de Tukey (=0,05). O momento do corte do pino de fibra de vidro não afetou a resistência de união quando o RelyX Unicem foi utilizado. No entanto, o corte do pino imediatamente após a cimentação reduziu os valores de resistência de união quando o RelyX ARC foi utilizado. Em conclusão, o momento do corte do pino pode afetar a resistência de união ao canal radicular quando o cimento resinoso convencional for utilizado.

Despite several advantages associated with pre-fabricated glass-fiber posts, the coronal portion of these posts must be cut to allow their use in various clinical situations. However, cutting the cemented post can generate stress on the bonding interface and affect the bond strength. The aim of this study was to investigate the effect the of fiber post cutting on the bond strength of root canals. Sixty bovine incisor roots were included in resin cylinders with simulated periodontal ligaments. Glass-fiber posts were luted using regular resin cement RelyX ARC (3M ESPE) or self-adhesive cement RelyX Unicem (3M ESPE). The posts were cut prior to cementation, immediately after luting or after building up the core (n=10). After storage for 24 h, the samples were cut and subject to push-out testing using a mechanical testing machine (EMIC DL 2000). Data were analyzed using two-way ANOVA (resin cement x moment of post cutting) and Tukey's post hoc test (α=0.05). The moment of fiber post cutting did not affect the bond strength when Unicem was used. However, the bond strength was reduced when ARC was used and when the post was cut immediately. In conclusion, the moment of fiber post cutting may affect the retention of root canal posts when a regular resin cement is used.

Introdução:Clinicamente, é comum observar os efeitos de estratificação de restaurações de compósito apenas após o polimento.Objetivo:Avaliar o efeito da técnica de polimento na transmitância de luz e na topografia de superfície de uma resina composta.Material e método:Amostras da resina Filtek Z-350 XT (cor A1E) foram confeccionadas em matriz metálica. Uma das superfícies das amostras recebeu acabamento com brocas de 12 lâminas e polimento através de uma das seguintes técnicas: SL (Sof-Lex), EH (Enhance) e DH (DHPro). Ausência de polimento foi usada como controle. Após o polimento, as amostras deviam apresentar espessura final de 1 mm. A transmitância de luz foi avaliada através do espectrofotômetro, sendo considerada apenas a luz no espectro visível. A topografia de superfície foi avaliada através de interferometria a laser, com os parâmetros Sdq (híbrido), St (amplitude máxima) e As (média de picos e vales). Os dados (n=5) foram submetidos a ANOVA e teste SNK. O teste de correlação de Pearson correlacionou Sdq, St e Sa à transmitância (α=0,05).Resultado:Todos os sistemas de polimento aumentaram a transmitância de luz em relação ao controle, não havendo diferença entre estes. Apenas as amostras polidas com SL e DH apresentaram maiores valores de Sdq que o Controle. Já para os parâmetros St e Sa, EH mostrou menores valores que o controle. Sdq e St mostraram correlação significativa com transmitância.Conclusão:Todos os sistemas de polimento foram efetivos em aumentar a transmitância, sendo a redução dos valores Sdq e St relacionada a esta modificação.

Introduction:Clinically, it is common to observe the effects of composite restorations stratification only after the polishing.Aim:This study evaluated the effect of polishing technique on light transmittance and surface topography of a composite resin.Material and method:Specimens of the composite resin Filtek Z-350 XT (color A1E) were built-up using a metal matrix. One of the specimens surfaces was finished with 12-blade burs and polished using one of following techniques: SL (Sof-Lex), EH (Enhance) and DH (DHPro). No polishing was used as control. After the polishing procedures, the samples were measured to check the final thickness (1 mm). The light transmittance was measured using a spectrophotometer connected to an integrating sphere, considered only light in the visible spectrum. The surface topography was measured by laser interferometer, assessing the parameters Sdq (hybrid), St (maximum amplitude) and Sa (average of peaks and valleys). Data (n=5) were submitted to ANOVA and SNK's test, while Pearson's correlation test was used to related Ssq, St and Sa to transmittance (α=0.05).Result:All polishing systems increased the light transmittance when compared to control, whereas no difference was observed between them. Only the samples polished with SL and DH showed lower Sdq values than control. Although for St and Sa parameters, EH showed lower values than those observed for control. Sdq and St showed significant correlation with transmittance.Conclusion:All polishing systems were effective to increase the transmittance, while the reduction of Sdq and St values were related to this modification.

Este estudo avaliou a influência do tipo de silano e a aplicação de temperatura no silano na resistência de união por push-out entre pinos de fibra de vidro com núcleo de preenchimento em resina composta e cimento resinoso. Cento e sessenta pinos de fibra de vidro (Exacto, Angelus, Londrina, PR, Brasil) receberam tratamento de superfície com peróxido de hidrogênio a 24%. Os pinos foram divididos em 8 grupos com dois fatores em estudo: temperatura de secagem de ar após a aplicação do silano (temperatura ambiente e 60 ºC) e o tipo de silano: três pré-hidrolisados - Silano (Angelus), Prosil (FGM), RelyX Ceramic Primer (3M ESPE) e um silano de dois frascos - Silane Coupling Agent (Dentsply). Para o teste de resistência de união entre pino e núcleo de preenchimento, os pinos (n=10) foram centralizados em uma matriz plástica cilíndrica e a resina composta (Filtek Z250 XT, 3M ESPE) foi incrementalmente inserida e fotopolimerizada. Para o teste de resistência de união entre pino e cimento resinoso (RelyX U100, 3M ESPE) 80 raízes de incisivos bovinos (n=10) foram preparadas e receberam os pinos de fibra de vidro. Teste de push-out foi usado para mensurar a resistência de união. Os dados foram analisados por ANOVA fatorial seguido do teste de Tukey (a=0,05). Temperatura e silano não tiveram influência na resistência de união entre núcleo de preenchimento e pino. Entretanto, para a resistência de união entre pino e cimento resinoso, o aumento da temperatura resultou em um melhor desempenho para Silane Coupling Agent, Silano e RelyX Ceramic Primer. Além disso, na temperatura ambiente Silane Coupling Agent teve a menor resistência de união. O efeito da secagem de ar quente é dependente da composição do silano. Concluindo, o uso do silano é influenciado pela molhabilidade dos materiais resinosos e os silanos pré-hidrolisados são mais estáveis comparados ao silano de dois frascos.

This study evaluated the influence of silane type and temperature of silane application on push-out bond strength between fiberglass posts with composite resin core and resin cement. One hundred and sixty fiberglass posts (Exacto, Angelus) had the surface treated with hydrogen peroxide 24%. Posts were divided in 8 groups according to two study factors: air-drying temperature after silane application (room temperature and 60 ºC) and silane type: three pre-hydrolyzed - Silano (Angelus), Prosil (FGM), RelyX Ceramic Primer (3M ESPE) and one two-component silane - Silane Coupling Agent (Dentsply). The posts (n=10) for testing the bond strength between post and composite core were centered on a cylindrical plastic matrix and composite resin (Filtek Z250 XT, 3M ESPE) that was incrementally inserted and photoactivated. Eighty bovine incisor roots (n=10) were prepared for testing the bond strength between post and resin cement (RelyX U100, 3M ESPE) and received the fiberglass posts. Push-out test was used to measure the bond strength. Data were analyzed by two-way ANOVA followed by Tukey's test (a=0.05). ANOVA revealed that temperature and silane had no influence on bond strength between composite core and post. However, for bond strength between post and resin cement, the temperature increase resulted in a better performance for Silane Coupling Agent, Silano and RelyX Ceramic Primer. At room temperature Silane Coupling Agent showed the lowest bond strength. Effect of the warm air-drying is dependent on the silane composition. In conclusion, the use of silane is influenced by wettability of resinous materials and pre-hydrolyzed silanes are more stable compared with the two-bottle silane.

Este estudo avaliou a influência de tratamentos de superfície de pinos de fibra de vidro na resistência de união à dentina radicular por meio do teste de push-out. Quarenta raízes de incisivos bovinos foram submetidas a tratamento endodôntico. A superfície dos pinos de fibra de vidro (Exacto #2, Angelus) foram tratadas com 4 protocolos diferentes (n=10): Controle - 70 % de etanol durante 1 min; 37 % de ácido fosfórico durante 1 min, 10% de ácido fluorídrico durante 1 min e 24 % de peróxido de hidrogênio durante 1 min. Depois foi aplicado agente de união silano por 1 min e todos os pinos foram cimentados com cimento resinoso auto-adesivo (RelyX Unicem, 3M- ESPE). As raízes foram seccionadas e foram obtidas duas fatias de 1 mm de espessura em cada terço: cervical, médio e apical. Os espécimes foram submetidos ao teste de push-out com uma velocidade de 0.5 mm/min. Os dados foram analisados pelo teste ANOVA com medidas repetidas, seguido pelo teste de Tukey HSD (=0,05). Os fatores tratamento de superfície (p<0,001) e região do terço radicular (p=0,007) foram significantes; no entanto, a interação entre os dois fatores não foi significante (p=0,827). A retenção ao canal radicular foi afetada pelo tipo de tratamento de superfície. O tratamento de superfície com 24% de peróxido de hidrogênio por 1 min rendeu significativamente maior resistência de união quando os pinos de fibra de vidro foram cimentados com RelyX Unicem.

This study evaluated the influence of the surface treatments of fiberglass posts on bond strength to root dentin using push-out test. Forty bovine incisor roots were endodontically treated. The surface of the fiberglass posts (Exacto #2, Angelus) were treated using 4 different protocols (n=10): Control - 70% ethanol for 1 min; 37% phosphoric acid for 1 min; 10% hydrofluoric acid for 1 min; and 24% hydrogen peroxide for 1 min. After a silane coupling agent was applied for 1 min and all posts were cemented using self-adhesive resin cement (RelyX Unicem, 3M-ESPE). The roots were sectioned and two 1-mm-thick slices were obtained from each third: cervical, middle and apical. The specimens were subjected to the push-out test with a crosshead speed of 0.5 mm/min. Data were analyzed by repeated measures ANOVA followed by Tukey's HSD tests (=0.05). The surface treatment (p<0.001) and root third region (p=0.007) factors were significant. The retention to root canal was affected by surface treatment type. The post surface treatment with 24% hydrogen peroxide for 1 min yielded significantly higher bond strength when the fiberglass posts were cemented with RelyX Unicem.

The aim of this study was to evaluate the effect of immediate and delayed photoactivation of self-adhesive resin cements (SARCs) on the retention of glass-fiber posts luted into root canals. Bovine incisors were endodontically treated, and post holes of 9 mm in depth were prepared. Fiber posts were luted using one of two SARCs, BisCem(r) (Bisco Inc., Schaumburg, USA) or RelyX Unicem clicker (3M ESPE, Saint Paul, USA), or a regular (etch-and-rinse) resin cement (AllCem; FGM, Joinvile, Brazil). Photoactivation was performed immediately, or at 5 or 10 min after cementation. Root/post specimens were transversely sectioned 7 days after luting into 1-mm-thick slices, which were submitted to push-out testing in a mechanical testing machine. Bond strength data were analyzed by two-way ANOVA and Student-Newman-Keuls' method (α = 0.05). Immediate photoactivation resulted in the highest bond strength for Unicem. BisCem(r) demonstrated higher bond strength values when photoactivated after a 10-min delay. Immediate photoactivation yielded the lowest bond strengths for AllCem, although no differences in bond strength were observed between photoactivation delayed by 5 and 10 min. In conclusion, the moment of resin cement photoactivation may affect the intraradicular retention of fiber posts, depending upon the resin cement used for luting.

The aim of this study was to evaluate the effect of treating intraradicular dentin with irrigating solutions on the retention of glass-fiber posts luted with self-adhesive resin cement. Bovine incisors were endodontically treated, and 9-mm-deep postholes were prepared. Before inserting the cement, the root canals were irrigated with various solutions: 11.5% polyacrylic acid for 30 s, 17% EDTA for 60 s, or 5% NaOCl for 60 s, respectively. Irrigation with distilled water was used in the control group. After all specimens had been rinsed with distilled water, the excess moisture was removed and the posts were luted using either BisCem (Bisco) or RelyX Unicem clicker (3M ESPE). Seven days after luting, the specimens were sectioned transversally into 1-mm-thick slices, which were submitted to push-out testing on a mechanical testing machine. Bond strength data (n = 6 per group) were analyzed by two-way ANOVA and Student-Newman-Keuls' test (α = 0.05). For Unicem, EDTA showed lower bond strength than the other solutions, which had similar results. For BisCem, EDTA showed higher bond strength than the other treatments, while application of NaOCl yielded higher bond strength than polyacrylic acid whereas the control group had intermediate results. In conclusion, irrigating root canals before insertion of self-adhesive resin cements, especially EDTA, might interfere with retention of the fiber posts.

One of the clinically relevant problems dentists face when restoring endodontically treated teeth is the mismatch between fiber post and post space diameters, which results in an excessively thick resin cement layer. Fiber post relining appears as a solution for this problem. OBJECTIVES: The aim of this study was to evaluate the effect of fiber post relining with composite resin on push-out bond strength. MATERIAL AND METHODS: Twenty bovine incisors were selected to assess post retention. The crowns were removed below the cementoenamel junction and the root canals were treated endodontically and flared with diamond burs. The roots were allocated into two groups (n=10): G1: fiber posts without relining and G2: fiber posts relined with composite resin. The posts were cemented with a dual-cured resin cement and the specimens were sectioned transversally. Three 1.5-mm thick slabs were obtained per root and identified as cervical, medium and apical thirds. The push-out test was performed at a crosshead speed of 0.5 mm/min until post dislodgement occurred. The failure mode of fractured specimens was analyzed under scanning electron microscopy. Data were analyzed by split-plot ANOVA and post-hoc Tukey's test at a pre-set alpha of 0.05. RESULTS: Relined fiber posts presented higher retention values than non-relined post in all thirds. No statistically significant differences (p>0.05) were found among thirds for relined posts. All failures occurred at the interface between resin cement and root dentin. CONCLUSIONS: Relining with composite resin seems to be an effective method to improve the retention of fiber posts to flared root canals.