Resumo Objetivo: Avaliar os resultados da instrumentação endodôntica e o tempo de preparo de lima odontopediátrica ativada por motor (Sequence Baby File- SBF) em canais de molares decíduos prototipados. Métodos: Trinta espécimes foram escaneados em micro-CT e divididos em três grupos de acordo com o tipo de instrumentação: mecanizada odontopediátrica (SBF); mecanizada convencional; lima K manual. O tempo de instrumentação foi cronometrado. Após o preparo, os espécimes foram escaneados novamente. As imagens pré e pós-instrumentação foram sobrepostas e a quantidade de desvio do canal radicular e a espessura de resina remanescente foram mensurados. Para as análises de comparações entre os grupos foram realizados teste ANOVA seguido do teste de Tukey (p<0,05). Resultados: Não ocorreram diferenças estatisticamente significativas entre os grupos no desvio do canal radicular (p>0,05). Houve diferenças estatisticamente significativas na comparação entre terços radiculares (p<0,001), mas sem diferenças significativas na interação grupo vs. terço radicular (p>0,05). A instrumentação mecanizada apresentou desgaste estatisticamente maior do que a instrumentação manual (p<0,001), sem diferenças estatísticas entre a SBF e a lima mecanizada convencional. A instrumentação mecanizada teve menor tempo de trabalho quando comparado a instrumentação manual (p<0,001). Conclusão: A instrumentação mecanizada odontopediátrica demonstrou bons resultados em relação ao desvio do canal radicular e quantidade de estrutura remanescente, com menor tempo de instrumentação. A SBF pode ser uma alternativa adequada para a instrumentação endodôntica em molares decíduos. Objetivo Sequence File prototipados Métodos microCT micro CT (SBF) convencional cronometrado novamente pósinstrumentação pós mensurados p<0,05. p005 p p<0,05 . 0 05 (p<0,05) Resultados p>0,05. p>0,05 (p>0,05) p<0,001, p0001 p<0,001 , 001 (p<0,001) vs p<0,001. Conclusão (SBF p00 p<0,0 (p<0,05 p>0,0 (p>0,05 p000 p<0,00 00 (p<0,001 p0 p<0, (p<0,0 p>0, (p>0,0 (p<0,00 p<0 (p<0, p>0 (p>0, p< (p<0 p> (p>0 (p< (p> (p

Abstract Evaluate the shaping ability and preparation time using a pediatric motor-driven rotary instrumentation compared to other systems in resin prototypes of primary molars. Methods: Thirty specimens were scanned in micro-CT and divided into three groups according to the instrumentation type: pediatric motor-driven Sequence baby File (SBF); conventional motor-driven (Sequence Rotary File - SRF); manual K file. Instrumentation time was timed. After preparation, the specimens were scanned again. The pre- and post-instrumentation images were superimposed to measure the amount of root canal deviation and the resin remnant thickness. ANOVA followed by the Tukey test analyzed the comparisons between groups (p<0.05). Results: No statistically significant differences occurred in root canal deviation among groups (p>0.05). There were statistically significant differences in the comparison among root thirds (p<0.001) but without significant differences in the interaction group vs. root third (p>0.05). Both motor-driven instrumentations showed statistically greater weariness than manual instrumentation (p<0.001), without significant significant differences between SBF and SRF. Motor-driven instrumentation had a shorter working time than manual instrumentation (p<0.001). Conclusion: Pediatric motor-driven instrumentation demonstrated good outcomes in relation to root canal deviation and amount of remnant structure, with shorter instrumentation time. SBF can be a suitable alternative for endodontic instrumentation in primary molars. motordriven motor driven molars Methods microCT micro CT type (SBF) SRF SRF) file timed again pre postinstrumentation post thickness p<0.05. p005 p p<0.05 . 0 05 (p<0.05) Results p>0.05. p>0.05 (p>0.05) p<0.001 p0001 001 (p<0.001 vs p<0.001, , Motordriven Motor p<0.001. Conclusion structure (SBF p00 p<0.0 (p<0.05 p>0.0 (p>0.05 p<0.00 p000 00 (p<0.00 p0 p<0. (p<0.0 p>0. (p>0.0 p<0 (p<0. p>0 (p>0. p< (p<0 p> (p>0 (p< (p> (p

Resumo O objetivo deste estudo foi avaliar a influência da temperatura nas propriedades de torção (resistência à torção e deflexão angular) de dois instrumentos rotatórios experimentais de NiTi fabricados com secção triangu.ar e tratamentos térmicos Blue e Gold. Quarenta instrumentos experimentais de NiTi 25.06 com tratamento térmico Blue e Gold foram usados (n= 20). Foi avaliada a resistência torcional e a deflexão angular até a fratura na temperatura ambiente (21°C ± 1°C) e corporal (36°C ± 1°C). O teste torcional foi realizado nos 3 mm da ponta dos instrumentos de acordo com a ISO 3630-1. A superfície fraturada de cada instrumento foi observada pelo microscópio eletrônico de varredura (MEV). Os dados foram analisados por meio do teste t não pareado para a comparação inter e intragrupos e o nível de significância à 5%. Os resultados demonstraram que a temperatura corporal não afetou a resistência a torção e deflexão angular quando comparada com a temperatura ambiente (P>0.05). No entanto, na temperatura de 36°C o instrumento com tratamento térmico Blue apresentou menor deflexão angular quando comparado com o Gold (P<0.05). Não houve diferença significante entre os dois instrumentos em relação a resistência à torção. A temperatura corporal não modificou a resistência torcional dos instrumentos fabricados com tecnologia Blue e Gold. No entanto, os instrumentos com NiTi Blue apresentaram menor deflexão angular do que o Gold a 36°C. trianguar triangu ar 2506 25 06 25.0 n= n (n 20. 20 . 20) 21°C 21C C 21 1°C 1C 1 36C 36 1°C. 36301. 36301 3630 1. 3630-1 MEV. MEV (MEV) 5 5% P>0.05. P005 P P>0.05 0 05 (P>0.05) entanto P<0.05. P<0.05 (P<0.05) 250 2 25. 363 3630- (MEV P00 P>0.0 (P>0.05 P<0.0 (P<0.05 P0 P>0. (P>0.0 P<0. (P<0.0 P>0 (P>0. P<0 (P<0. P> (P>0 P< (P<0 (P> (P< (P

Abstract This study aimed to evaluate the influence of temperature on torsional strength and angular deflection of two experimental NiTi rotary instruments manufactured from Blue and Gold thermal treatments and with identical cross-sections. A total of 40 experimental NiTi instruments 25.06 and with a triangular cross-section and manufactured from Blue and Gold thermal treatments were used (n=20). The torsional test was performed in the 3 mm from the tip of the instrument according to ISO 3630-1. The torsional test evaluated the torsional strength and angular deflection to failure at room temperature (21°C ± 1° C) and body temperature (36°C ±1°C). The fractured surface of each fragment was observed by using scanning electron microscopy (SEM). Data were analyzed using an unpaired t test for inter and intra-group comparison and the level of significance was set at 5%. The results showed that the body temperature did not affect the torsional strength and angular deflection of the instruments when compared with room temperature (P>0.05). However, at body temperature, the Blue NiTi instruments presented significantly lower angular deflection in comparison with Gold NiTi instruments (P<0.05). There was no significant difference regarding the torsional strength of the instruments at body temperature (P>0.05). The temperature did not affect the torsional strength of the instruments manufactured from Blue and Gold technology. However, the Blue NiTi instruments presented significantly lower angular deflection than Gold instruments at 36°C temperature. crosssections. crosssections cross sections. sections cross-sections 4 2506 25 06 25.0 crosssection section n=20. n20 n n=20 . 20 (n=20) 36301. 36301 3630 1. 1 3630-1 21°C 21C C 21 36C 36 ±1°C. 1C ±1°C ±1°C) SEM. SEM (SEM) intragroup intra group 5 5% P>0.05. P005 P P>0.05 0 05 (P>0.05) However P<0.05. P<0.05 (P<0.05) technology 250 2 25. n2 n=2 (n=20 363 3630- (SEM P00 P>0.0 (P>0.05 P<0.0 (P<0.05 n= (n=2 P0 P>0. (P>0.0 P<0. (P<0.0 (n= P>0 (P>0. P<0 (P<0. (n P> (P>0 P< (P<0 (P> (P< (P

Abstract This study aimed to assess the self-reported levels of confidence and knowledge related to non-odontogenic pain among a group of Brazilian endodontists. Methodology A total of one hundred and forty-six endodontists affiliated with the Brazilian Society of Endodontics participated in the survey. The questionnaire, distributed via email or WhatsApp, contained inquiries designed to gauge self-perceived confidence and knowledge concerning non-odontogenic pain. The practitioners were categorized into four groups based on their self-reported familiarity with various orofacial pain types, classified as either sufficient or insufficient, and on their engagement in ongoing educational programs related to orofacial pain. Data were analyzed by Chi-Square Test and Fischer’s exact test (p<0.05). Results Overall, self-reported confidence about non-odontogenic pain was high, especially for endodontists who considered their knowledge about orofacial pain sufficient, regardless of whether they had (71.1% - 97.8%) or not (35.7% - 96.4%) been continuously involved in education courses on orofacial pain. In general, self-reported knowledge about non-odontogenic pain was insufficient (0% - 42%), except in the question about how they would act in cases of pain that persists beyond the normal healing time after an endodontic procedure (70.6% - 81.9%). In general, endodontists are confident in their diagnosis and treatment of non-odontogenic pain. Nonetheless, this confidence did not correlate with a commensurate knowledge depth of. Thus, specialization courses in endodontics should highly consider training and qualifying these professionals in the diagnosis of non-odontogenic pain. selfreported self reported nonodontogenic non odontogenic fortysix forty six survey questionnaire WhatsApp selfperceived perceived types ChiSquare Chi Square Fischers Fischer s p<0.05. p005 p p<0.05 . 0 05 (p<0.05) Overall high 71.1% 711 71 1 (71.1 97.8% 978 97 8 35.7% 357 35 7 (35.7 96.4% 964 96 4 general 0% (0 42%, 42 42% , 42%) 70.6% 706 70 6 (70.6 81.9%. 819 81.9% 81 9 81.9%) Nonetheless Thus p00 p<0.0 (p<0.05 71.1 (71. 97.8 35.7 3 (35. 96.4 ( 70.6 (70. 81.9 p0 p<0. (p<0.0 71. (71 97. 35. (35 96. 70. (70 81. p<0 (p<0. (7 (3 p< (p<0 (p< (p

Abstract This study aimed to evaluate physicochemical properties of three ready-to-use calcium silicate-based endodontic sealers: Endosequence BC Sealer, Bio C Sealer, and Sealer Plus BC. Radiopacity was evaluated using specimens of 10 mm in diameter and 1 mm in height, along with an aluminum step wedge. For the flow test, 0.5 mL of each sealer was deposited between glass plates and the mean of the measurement of two diameters was considered the cement flow value. For pH and calcium release, root canals of 30 prototypes of upper incisor acrylic resin teeth were filled with sealer and gutta percha point and then immersed in containers with 13 mL of ultrapure water. Both pH and release of calcium ions (atomic absorption spectrophotometer) were measured at 3, 24, 72, and 168 h. Acrylic resin teeth were scanned by Micro-CT 1174 at the time of pH and calcium ion readings for volumetric change analysis. The data were analyzed by ANOVA, Tukey’s, Kruskal-Wallis, and Dunn’s tests. Endosequence BC Sealer presented the lowest, and Bio C Sealer the highest volumetric change after 72 h and 168 h (p < 0.05). Endosequence BC Sealer presented higher radiopacity (p < 0.05). All materials showed alkalinization capacity. All of them presented calcium ion release, with a higher value for Sealer Plus BC. All materials presented alkalinization, calcium release capacity, radiopacity, and flow above the minimum values required by the ISO standard. The highest volumetric loss was experienced by Bio C Sealer and the lowest one by Endosequence BC Sealer.

Abstract Background: The association of scaffolds to repair extensive bone defects can contribute to their evolution and morphophysiological recomposition. The incorporation of particulate biomaterials into three-dimensional fibrin bioproducts together with photobiomodulation therapy (PBM) has potential and can improve regenerative medicine procedures. The objective of this experiment was to evaluate the effects of PBM therapy on critical size defects filled with xenogenic bone substitute associated with fibrin biopolymer. Methods: A critical defect of 8 mm was performed in 36 Wistar male adult rats that were divided into four groups. Groups BC and BC-PBM were defined as controls with defects filled by a clot (without or with PBM, respectively) and groups XS and XS-PBM that comprised those filled with biocomplex Bio-OssTM in association with fibrin biopolymer. PBM was applied immediately after the surgery and three times a week every other day, with the parameters: wavelength of 830 nm, energy density 6.2 J/cm2, output power 30 mW, beam area of 0.116 cm2, irradiance 0.258,62 W/cm2, energy/point 0.72 J, total energy 2.88 J. Fourteen and 42 days after the surgery, animals were euthanatized and subjected to microtomography, qualitative and quantitative histological analysis. Results: The BC-PBM and XS-PBM groups had a similar evolution in the tissue repair process, with a higher density of the volume of new formed bone in relation to the groups without PBM (p = 0.04086; p = 0.07093, respectively). Intense vascular proliferation and bone deposition around the biomaterial particles were observed in the animals of the groups in which biocomplex was applied (XS and XS-PBM). Conclusion: PBM therapy allowed an improvement in the formation of new bone, with a more organized deposition of collagen fibers in the defect area. Biocomplex favored the insertion and permanence of the particulate material in bone defects, creating a favorable microenvironment for accelerate repair process.

Abstract The aim of this study was to evaluate the quality of curved root canal preparation, torsional fatigue, and cyclic fatigue of rotary systems manufactured with different NiTi alloys. Ninety single-rooted canals with curvatures of 15° to 30o were scanned and divided into three groups according to the rotary system used: BT-Race (BTR) – 10.06, 35.00, 35.04; SequenceRotaryFile (SRF) – 15.04, 25.06, 35.04; and ProDesignLogic (PDL) – 25.01, 25.06, 35.05. Each system was used on three specimens. The teeth were prepared, scanned, and analyzed to assess increase in volume, transportation, and centering ability of the root canal. Torsional fatigue of glide path instruments (BTR 10.06, SRF 15.04 and PDL 25.01) and cyclic fatigue of the finishing instrument (BTR 35.04, SRF 35.04 and PDL 35.05) were obtained by analyzing completely new instruments (n = 10) and instruments after they had been used three times (n = 10). After the torsional and cyclic fatigue tests, the fractured surface of the new and used instruments were examined by scanning electron microscopy. Increase in volume, canal transportation, and centering ability showed no significant differences among the groups (p > 0.05). The torsional test showed that SRF 15.04 produced the highest torque values for both new and used instruments, followed by PDL 25.01 and BTR 10.06 (p < 0.05). PDL 25.01, both new and used, exhibited higher values of angular deflection followed by SRF 15.04 and BTR 10.06 (p < 0.05). As regards cyclic fatigue, use of PDL 35.05, both new and used, required a longer time and larger number of cycles than did SRF 35.04 and BTR 35.04 (p < 0.05). Clinical use affected the torsional fatigue of BTR; however, cyclic fatigue was not significantly affected (p < 0.05). All rotary systems were able to prepare the curved canals satisfactorily and were used safely on the three specimens. Relative to torsional fatigue, SRF 15.04 exhibited a higher torque, and PDL 25.01, higher angular deflection. BTR 10.06 was the most affected by clinical use. PDL 35.05 showed greater resistance to cyclic fatigue.

Abstract: Sixty moderately curved canals of mandibular molars classified as Vertucci’s type IV canal configuration were selected by micro-CT 1174. The teeth were divided into two groups according to the kinematics used, whether reciprocating or rotary motion (n=30, totaling 60 mesial root canals). The instruments used to perform the glide path procedures had identical features (0.15 mm of tip size, 0.04 mm/mm taper, thermal treatment, and square cross-section), but differed in the direction of the cutting blade. The duration of the procedure and the absolute and percentage frequency of the instruments to reach the full working length were recorded. The torsional test (3630-1; 1992) was performed on both used and unused instruments, to evaluate a possible reduction in the torsional resistance when using the glide path procedure. Statistical analysis was performed using the unpaired t-test and the chi-square test, and the level of significance was set at 5%. The type of kinematics used affected the duration of glide path procedures, and the reciprocating motion seemed to induce less torsional stress during glide path procedures.

Abstract Isthmuses are reported as common anatomic complexities in teeth often associated with failures in endodontic treatment. They should be considered before starting treatment and a preoperative computed tomography scan (CT) may demonstrate these complexities. Objective To assess the diagnostic value of the highest resolution settings of a cone-beam CT (CBCT) system in identifying and measuring apical isthmuses, using micro-CT as reference. Methodology After micro-CT scanning, 40 humans’ lower first molars with isthmuses in the apical-3 mm of mesial roots were scanned by the highest resolution settings of the New Generation i-Cat ® CBCT equipment. Two blinded observers recorded the detection of isthmuses in CBCT scans. The lengths of isthmuses were compared between micro-CT and CBCT to assess the diagnostic value of CBCT. Quantitative data for sensitivity were represented as percentages (95% confidence interval). The Bland-Altman method was used to assess differences between gold standard lengths (micro-CT) and CBCT lengths. Results BCT demonstrated 30 positive findings, representing sensitivity for isthmus identification of 75% (95% CI=0.4114–1.1364). Differences between the lengths in micro-CT (1.99±0.40 mm) and CBCT (1.53±0.41 mm) were significant (p<0.0001). Conclusion The CBCT device used presented limited diagnostic value in the identification and measurement of apical isthmuses in the mesial roots of lower molars. In some cases, the actual anatomy of the apical root canal may not be completely delineated in this type of CBCT system, even using the highest resolution settings.

Abstract To evaluate the influence of novel ultrasonic tips as an auxiliary method for the rotary preparation of flattened/oval-shaped canals. Forty-five mandibular incisors were selected and divided into one of three experimental groups (n = 15): Group PFCP – ProDesign Logic 25/.05 + Flatsonic + Clearsonic + Prodesign Logic 40/.01; Group FCP – Flatsonic + Clearsonic + ProDesign Logic 40/.01; and Group PP – Prodesign Logic 25/.05 + Prodesign Logic 40/.05. The teeth were scanned preoperatively and postoperatively using microcomputed tomography. The percentage values for increase in volume, non-instrumented surface area, dentin removal, degree of canal transportation, and centering ratio between the experimental groups were examined. Data were analyzed using the non-parametric Kruskal-Wallis and Dunn’s tests (p < 0.05). Group PFCP showed the greatest volume increase in the total portion of the root canal and the lowest percentage of non-instrumented surface area. Regarding the degree of transportation in the buccolingual direction, statistically significant differences between groups PFCP and PP were observed at the coronal third of the canal. In the mesiodistal direction, no statistically significant differences were observed at the coronal, middle, and apical thirds. As for the centering ratio, statistically significant differences were found in the buccolingual direction. In the mesiodistal direction, no statistically significant differences were observed at the coronal, middle, and apical thirds. The use of novel ultrasonic tips combined with rotary instruments in group PFCP provided a significant increase in volume and reduced the percentage of non-instrumented areas during the preparation of flattened/oval-shaped canals.

Abstract To evaluate the torsional properties of engine-driven pathfinding instruments manufactured from different NiTi alloys – R-Pilot (tip size 12.5;.04 taper; M-Wire) and One G (tip size 14;.03 taper; Conventional NiTi). A total of 40 NiTi instruments from engine-driven pathfinding instruments (n = 20) were used. The torsion tests followed ISO 3630-1 (1992). Three millimeters of each instrument tip was fastened to a small load cell by a lever arm linked to the axis of torsion. During the test, the torsion testing machine software measured the maximum torsional strength and angle of rotation (0) before instrument failure. The fractured surface of each instrument was assessed by scanning electron microscopy (SEM). In addition, a supplementary examination was performed to measure the cross-sectional area and the metal mass volume of each instrument 3 mm from the tip. Data were analyzed using a t-test, with significance level set at 5%. R-pilot had significantly higher torsional strength than did One G (p < 0.05). Regarding the angle of rotation to fracture, One G had higher angles than did R-Pilot (p < 0.05). The supplementary examination showed that R-Pilot had the highest cross-sectional area and volume of metal mass at 3 mm from the tip (p < 0.05). R-pilot (M-Wire NiTi alloy) had a significantly higher torsional strength and One-G (superelastic NiTi alloy) had the highest angle of rotation to fracture.

Abstract The aim of this study was to evaluate the influence of a novel ultrasonic tip as an auxiliary method for removing filling material from flattened/oval-shaped canals. The null hypothesis tested was that this method does not influence removing the filling material in flattened/oval-shaped canals. Forty-five mandibular incisors were selected and randomly divided into three experimental groups (n = 15) according to different protocols for removing root canal filling material. Group R: Reciproc R25/.08, Group RC: Reciproc R25/.08 + Clearsonic tip, and Group CR: Clearsonic tip + Reciproc R25/.08. The teeth were scanned pre and post-operatively by means of a micro-computed tomography system. Data were analyzed using non-parametric Kruskal-Wallis and Dunn tests (p < 0.05). The percentage of residual root canal filling material between the experimental groups was examined. Statistically significant differences between the experimental groups were found in the root canal. Group R had the highest percentage of residual root canal filling material when compared with Groups RC and CR. The lowest percentage of residual root canal filling material was observed in Group CR. In the apical third of the root canal, statistically significant differences were found between the different protocols. The use of the ClearSonic tip followed by the Reciproc 25/.08 file to remove filling material resulted in the lowest percentage of residuals in the whole root canal and in the apical third.

Abstract The aim of this study was evaluate the influence of ultrasonic activation (UA) of AH Plus to improve canal and isthmus filing, and analyse the antimicrobial effect against Enterococcus faecalis within dentinal tubules. Material and Methods: Thirty mesial roots of mandibular first molars were selected and divided into 2 groups (n = 15): with and without UA of the sealer. Then the root canals were filled by using the single cone technique, and the specimens were sectioned at 2, 4 and 6 mm from the apex for stereomicroscope and confocal laser scanner microscopy (CLSM) analysis. In addition, 30 bovine incisors were contaminated with Enterococcus faecalis and divided into 3 groups (n = 10). The specimens were obturated by using the single cone technique with (G1) and without (G2) UA of the sealer and G3 as the control group. All were sectioned into 6 mm-long cylinders and stained with LIVE/DEAD to assess bacterial viability by CLSM. Results: The UA of the sealer significantly reduced the presence of unfilled areas in the canal and isthmus area in all sections (p<0.05), and there was a significant increase in sealer penetration in both canals and isthmuses (p<0.05). As regards gaps, a significant reduction was found at 2 and 6 mm in the isthmus area of the UA group (p<0.05). Moreover, UA of the sealer significantly reduced bacterial viability in the superficial dentine when compared with the other groups (p<0.05). Conclusion: Ultrasonic activation of the AH Plus sealer promoted a better quality of root canal filling and increased the intratubular penetration of sealer, especially in the isthmus area. Additionally, ultrasonic activation of the sealer increased the intradentinal antimicrobial action against Enterococcus faecalis, mainly in the superficial dentine of the root canal.

RESUMO Objetivo o estudo teve como objetivo desenvolver e avaliar um website com informações na área de Fonoaudiologia com enfoque no processo de envelhecimento. Método foi elaborado um website contendo informações com linguagem simples, objetivo claro e conteúdo conciso, baseado em evidências científicas. Utilizou-se o índice de Flesch para verificar a legibilidade do material, encontrando-se, em 50% do conteúdo, o correspondente a “fácil” e, em 50% do conteúdo, o correspondente a “difícil”. A elaboração do website seguiu as etapas: análise e planejamento, modelagem, implementação e avaliação. Foram convidados avaliadores que fizeram parte das categorias: idoso, cuidador de idoso e fonoaudiólogo. A amostra foi composta por 10 idosos, 8 cuidadores de idosos e 10 fonoaudiólogos. A análise estatística foi realizada por meio do teste Kruskal-Wallis e Coeficiente de Correlação de Spearman. Resultados o conteúdo do website foi avaliado como “adequado” e a qualidade técnica do website apresentou-se como “excelente”. Conclusão conclui-se que o website pode ser considerado um material acessível, que compõe uma fonte de consulta e de complementação de informações sobre a temática, além de uma importante ferramenta para efetivar o processo de transmissão de informação.

ABSTRACT Purpose This research aimed to develop and evaluate a website with information on Speech-language therapy area with focus on the aging process. A website containing information with simple language, clear purpose and concise content was designed based on scientific evidence. Methods The Flesch Index was used to check the material readability, with 50% of the content corresponding to “easy” and 50% of the content corresponding to “difficult”. The website development followed the steps: analysis and planning, modeling, implementation and evaluation. Evaluators invited to participate were part of the following categories: elderly people, caregivers and speech-language therapists. The sample consisted of 10 elderly, 8 caregivers and 10 speech-language therapists. Most individuals (89.28%) were females, who often accessed the Internet (78.57%) and had different educational levels. Results Statistical analyses were performed using the Kruskal-Wallis test and Spearman correlation coefficient. The website's content was classified as “adequate” and the website’s technical quality as “excellent”. There was no statistically significant difference between the categories and subscales or the overall score. Conclusion The website can be considered an accessible material, and a source of consultation and complementation of information about the theme, as well as an important tool for effecting the information transmission process.

Resumo O objetivo deste estudo foi avaliar a influência de diferentes protocolos de irrigação ultrassônica passiva na remoção de detritos em sulcos artificialmente criados nos terços radiculares cervical, médio e apical. Quarenta raízes de incisivos bovinos extraídos foram instrumentadas a 1 mm do ápice radicular com um instrumento R50 Reciproc e irrigadas com hipoclorito de sódio a 2,5%. As raízes foram então inseridas numa mufla e clivadas em duas hemisecções. Sulcos (3 mm de comprimento) foram feitos a 2, 7 e 12 mm do ápice radicular em uma hemisecção e preenchidos com detritos dentinários. As hemisecções foram reagrupadas na mufla e divididas em 4 grupos (n = 10) de acordo com o protocolo de irrigação final: Grupo controle: 3x20 s usando agulha de calibre #30 sem agitação da solução irrigadora; Grupo PUI-s (static passive ultrasonic irrigation): 3x20 s de irrigação ultra-sônica passiva com a ponta do inserto mantida estática no terço apical; Grupo PUI-t (Irrigação ultrassônica passiva por terço): 20 s de PUI em cada terço; Grupo PUI-d (Irrigação ultrassônica dinâmica): 3x20 s de PUI movendo dinamicamente o inserto em toda extensão do canal radicular. Em todos os grupos, foi utilizado um total de 6 mL de hipoclorito de sódio a 2,5% como irrigante. Após estes procedimentos, os sulcos foram analisadas com um estereomicroscópio e pontuações foram atribuídas quanto à remoção dos detritos. Os dados foram analisados estatisticamente (a=0.05). Os resultados mostraram uma melhor limpeza em todos os grupos onde a solução de irrigação foi agitada com dispositivo ultrassônico do que no grupo controle (p<0,05). No terço apical, o PUI-d e o PUI-s apresentaram performance semelhantes (p>0,05) e melhor limpeza do que o PUI-t (p<0,05). Os métodos dinâmico e estático de agitação da solução de irrigação proporcionaram uma limpeza mais eficaz. O PUID promoveu os sulcos mais completamente limpos sugerindo que seu uso é o mais adequado em casos de dentes com anatomia de canal complexa.

Abstract The aim of this study was to evaluate the influence of different passive ultrasonic irrigation protocols on the removal of debris in artificially created grooves in the cervical, middle and apical root thirds. Forty extracted bovine incisor roots were instrumented to 1 mm of the root apex with a R50 Reciproc instrument and irrigated with 2.5% sodium hypochlorite. The roots were then inserted in a muffle and cleaved into two hemisections. Grooves (3-mm long) were done at 2, 7 and 12 mm from the root apex in one hemisection and filled with dentinal debris. The hemisections were regrouped into the muffle and divided into 4 groups (n=10) according to the final irrigation protocol: Control group: 3x20 s using a #30 gauge needle without agitation of the irrigating solution; Group PUI-s (static passive ultrasonic irrigation): 3x20 s of passive ultrasonic irrigation with the tip of the insert maintained static on the apical third; Group PUI-t (passive ultrasonic irrigation per third): 20 s of PUI in each third; Group PUI-d (passive dynamic ultrasonic irrigation): 3x20 s of PUI dynamically moving the insert in the whole extent of the root canal. In all groups, was used a total of 6 mL of 2.5% sodium hypochlorite as irrigant. After these procedures, the grooves were analyzed with a stereomicroscope and assigned scores as regards removal of the debris. The data were analyzed statistically (a=0.05). The results showed a better cleaning in all the groups where the irrigating solution was agitated with ultrasonic device than in the control group (p<0.05). In the apical third, the PUI-d and PUI-s showed similar performance (p>0.05) and a better cleanness than PUI-t (p<0.05). The dynamic and static methods of agitation of the irrigating solution provided more effective cleaning. PUI-d provided the most completely clean grooves suggesting that its use is the most adequate in cases of teeth with complex canal anatomy.