Metastable β-type Ti alloys with non-toxic addition elements such as Mo, Zr, Sn, Ta and Nb were developed as an alternative to the widely used Ti-6Al-4V alloy for biomedical applications. These alloys possess enhanced biocompatibility and reduced elastic modulus in comparison with Ti-6Al-4V. Moreover, for orthopedic implants, low Young's modulus is required in order to avoid the stress shielding phenomenon. This study analyzes the microstructure and mechanical properties of a new Ti-12Mo-8Nb alloy after hot swaging, annealing at 950 ºC for 1h and water quenching. The alloy was characterized by X-ray diffraction, optical microscopy and transmission electron microscopy. Tensile tests were performed at room temperature. Young's modulus and hardness values were also measured. The structural characterization reveals a metastable β structure containing only a small amount of α and ω phases. Exhibiting a lower Young's modulus than Ti-6Al-4V and other previously studied Ti-Mo-Nb alloys, the Ti-12Mo-8Nb alloy can be a promising alternative for orthopedic application.

Resumo: A diluição é um evento de forte influência na microestrutura e, consequentemente, nas propriedades de revestimentos soldados. O presente estudo avaliou o efeito do nível de diluição na microestrutura da zona fundida de revestimentos da liga Inconel 686. Os revestimentos foram depositados por processo TIG com alimentação de arame frio. A diluição foi calculada a partir das características geométricas dos revestimentos e por medidas de composição química de EDS e de espectroscopia de emissão ótica. As microestruturas de todos os revestimentos foram compostas por uma matriz γ-CFC com alguns precipitados secundários. Essas partículas são chamadas de fases topologicamente compactas. Esses precipitados assumiram diversos aspectos morfológicos, nos quais os precipitados com morfologia disforme foram observados com maior frequência em todos os revestimentos avaliados, independentemente do nível de diluição. Uma fase com morfologia lamelar, que estabelece uma relação de orientação com a matriz γ-CFC na direção de solidificação, foi observada nos revestimentos de menor diluição. Além disso, uma fase com morfologia disforme com uma fina precipitação agregada foi observada nos revestimentos mais diluídos.

Abstract: The dilution is an event that have a high influence on the microstructure and, consequently, in the properties of weld claddings. The present study evaluated the effect of dilution level on the microstructure of the fusion zone of alloy Inconel 686 weld claddings. The claddings were welded by the TIG cold wire feed process. The dilution was calculated from the geometric characteristics and based on chemical composition of the materials obtained by energy dispersive X-ray spectroscopy and optical emission spectroscopy. The microstructure of all claddings were composed by a γ-FCC matrix with some minor precipitates. These particles are called in literature as topologically closed-packed phases (TCP). These precipitates assumed several morphological aspects, being the shapeless morphology observed in more frequency in all claddings evaluated, independent of dilution level. A phase with lamellar morphology, which growth establishing an orientation relationship with the γ-FCC matrix solidification direction, was observed only in claddings with a low dilution level. In addition, a shapeless phase with a fine precipitation aggregated was observed in claddings with a high dilution level.

β-metastable titanium alloys with high strength to Young’s modulus ratio have been developed by different authors aiming their use as biomaterials for hard tissue replacement. However, it is not easy to combine low elastic modulus with high mechanical strength. In this work, a β-Ti alloy (Ti-10Mo-20Nb) was produced by arc-melting, then homogenized, cold swaged and aged in order to obtain fine α-Ti precipitates in a β-Ti matrix. The microstructures were characterized by transmission electron microscopy and X-ray diffraction. Mechanical properties characterization was based on Vickers microhardness tests and Young’s modulus measurements. The cold swaged material subjected to an ageing treatment at 500 °C for 4 h showed the highest hardness/ Young’s modulus ratio, associated to very fine α phase precipitates in a β-Ti matrix.

Beta titanium alloys were developed for biomedical applications due to the combination of its mechanical properties including low elasticity modulus, high strength, fatigue resistance, good ductility and with excellent corrosion resistance. With this perspective a metastable beta titanium alloy Ti-12Mo-13Nb was developed with the replacement of both vanadium and aluminum from the traditional alloy Ti-6Al-4V. This paper presents the microstructure, mechanical properties of the Ti-12Mo-13Nb hot swaged and aged at 500 °C for 24 h under high vacuum and then water quenched. The alloy structure was characterized by X-ray diffraction and transmission electron microscopy. Tensile tests were carried out at room temperature. The results show a microstructure consisting of a fine dispersed α phase in a β matrix and good mechanical properties including low elastic modulus. The results indicate that Ti-12Mo-13Nb alloy can be a promising alternative for biomedical application.

This study has investigated the niobium (Nb) additions effect on both microstructure and heat-treated Ti-10Mo-xNb (x = 3, 6 and 9) alloys mechanical properties. The microstructures were characterized by optical microscopy, X-ray diffraction and transmission electron microscopy. The mechanical characterization was carried out by Vickers microhardness test and Young's modulus measurements. The outcomes show that the addition of Nb in alloys decreased the proportion of ω and α' phases. The Ti-10Mo-3Nb alloy presented the best hardness and elastic modulus combination among the three developed alloys and also with respect to Ti-6Al-4V alloy and commercially pure Ti.