Abstract Textile sludge is a waste from the effluent treatment of textile laundries and its incorporation into alternative materials has been proposed as a possibility for its disposal. A systematic search was carried out in literature from this perspective, aiming to observe concentrations of waste material and its preparation, matrices used, technological performance and immobilization of textile waste. The matrices used were mortars, concretes and ceramic bricks, in general, deleterious effects were observed on mechanical characteristics of the materials produced. In concrete and mortars, the fineness had an impact on increase in water demand, which increased mixtures porosity; and organic matter and heavy metals, in cement hydration. Recent studies therefore proposed waste material pre-treatment as a favorable alternative. Increases in porosity also occurred in ceramic bricks, however, due to high organic matter content. Regarding waste immobilization, cementitious materials showed satisfactory performance; ceramic bricks, on the other hand, obtained some results outside the normative limits. Therefore, it is necessary to expand discussions regarding the pre-treatment carried out on textile sludge, as well as its impacts on mechanical and environmental performance.

Resumo Olodo têxtil é um resíduo do tratamento do efluente das lavanderias têxteis e sua incorporação em materiais alternativos tem sido proposta como possibilidade para sua destinação. Foi realizada uma busca sistemática na literatura nesta perspectiva, visando observar as concentrações de material residual e seu preparo, as matrizes utilizadas, o desempenho tecnológico e imobilização do resíduo têxtil. As matrizes empregadas foram argamassas, concretos e tijolos cerâmicos, sendo observados, de maneira geral, efeitos deletérios nas características mecânicas dos materiais produzidos. Em concretos e argamassas, a finura impactou no aumento da demanda de água, o que elevou a porosidade das misturas; e a matéria orgânica e metais pesados, na hidratação do cimento. Estudos recentes propuseram, então, o pré-tratamento do material residual como uma alternativa favorável. Incrementos na porosidade também ocorreram nos tijolos cerâmicos, porém, devido ao elevado teor de matéria orgânica. Quanto a imobilização do resíduo, os materiais cimentícios apresentaram desempenho satisfatório; já os tijolos cerâmicos, obtiveram alguns resultados fora dos limites normativos. Portanto, é necessário ampliar as discussões quanto ao pré-tratamento realizado no lodo têxtil, bem como seus impactos no desempenho mecânico e ambiental.

Abstract Given the environmental impacts associated with the production of conventional Portland cement, the study of special cements with reduced environmental impact has been a trend. In this context, cements containing ye'elimite (YCC) stand out due to their low CO 2 emissions. Despite the environmental advantages, the high demand for aluminum economically limits the production of these cements.An alternative to making its production feasible is using residual raw materials as a source of Al 2 O 3 , such as SFCC (spent fluidized catalytic cracking).In view of this, this work aims to evaluate hydration at the initial age of cements. For this, six clinkers were produced with different ye'elimite contents, with and without SFCC. These were characterized by XRD/Rietveld. The pastes were evaluated by TG/DTG and XRD/Rietveld to understand the hydration mechanism on the third day of these cements. It was possible to synthesize the main phases of YCC, in clinkers with and without SFCC. In addition, at the age evaluated, the pastes with and without SFCC presented comparable phase composition, indicating the potential for co-processing this residue.

Resumo Diante dos impactos ambientais associados à produção do cimento Portland convencional, o estudo de cimentos especiais de reduzido impacto ambiental tem sido uma tendência. Neste contexto, os cimentos contendo ye’elimita (YCC) se destacam devido à baixa emissão de CO2. Apesar das vantagens ambientais, a alta demanda por alumínio limita economicamente a produção destes cimentos. Uma alternativa para viabilizar a sua produção é o uso de matérias-primas residuais como fonte de Al2O3, a exemplo do SFCC (catalizador gasto do craqueamento catalítico de leito fluidizado). Diante disso, este trabalho tem como objetivo avaliar a hidratação na idade inicial de cimentos YCC produzidos a partir do coprocessamento do SFCC. Para isso, foram produzidos seis clínqueres com diferentes teores de ye’elimita, com e sem SFCC. Estes foram caracterizados por DRX/Rietveld. As pastas foram avaliadas por TG/DTG e DRX/Rietveld para compreender o mecanismo de hidratação em idade inicial destes cimentos. Foi possível sintetizar as principais fases dos YCC, nos clínqueres com e sem SFCC. Além disso, na idade avaliada, as pastas com e sem SFCC apresentaram composição de fases comparáveis indicando o potencial de coprocessamento do SFCC neste tipo de cimento.

Abstract Incorporating BIM in the education of professionals has become a demand and a topic of high importance for higher education. Several proposals for a curricular implementation of BIM exist. However, in most cases, they are specific to a single university or domain, do not consider academic policies or simplify practice by segmenting knowledge. This work proposes a protocol for the curricular implementation of BIM similar to the industry, considering aspects of process, technology, and policies aligned with the educational institution's mission and with existing competencies. Action research was the used method. Three actions were conducted: (1) proposition, (2) systematization and (3) application. The actions were executed in cycles incrementally, resulting in (1) guidelines, (2) supporting tools and (3) implementation plans. Two Brazilian universities participated in pilot studies of Project Construa Brasil. The pilot studies inspired a network of BIM cells that have synchronously applied curricular BIM implementation guidelines on a large scale. The guidelines proved to be generic and comprehensive, guiding the transformation with an empirical basis for the academics' decision-making. Leadership of a BIM specialist was confirmed as an essential factor of success. It is observed that even with a timid introduction of BIM competence in a limited scope of engineering solutions, the impact on the BIM maturity curriculum is significant.

Resumo Incorporar o BIM na formação de profissionais tornou-se uma demanda e um tema de grande importância para o ensino superior. Existem várias propostas de implementação curricular do BIM. No entanto, na maioria dos casos, são específicos de uma única universidade oudomínio, não contemplam políticas acadêmicas ou simplificam a prática segmentando o conhecimento. Este trabalho propõe um protocolo para a implementação curricular do BIM semelhante aoda indústria, considerando aspectos de processo, tecnologia e políticas alinhados com a missão da instituição de ensino e com as competências existentes. Pesquisa-ação foi o método utilizado. Três ações foram realizadas: (1) proposição, (2) sistematização e (3) aplicação. As ações foram realizadas em ciclos de forma incremental, resultando em (1) diretrizes, (2) ferramentas de apoio e (3) planos de implementação. Duas universidades brasileiras participaram de estudos-piloto do Projeto Construa Brasil. Os estudos-piloto inspiraram uma rede de células BIM que aplicaram as diretrizes curriculares de implementação BIM em larga escala. As diretrizes mostraram-se genéricas e abrangentes, orientando a transformação com base empírica para a tomada de decisão dos acadêmicos. A facilitação de um especialista BIM foi confirmada como fator essencial de sucesso. Observa-se que, mesmo com uma tímida introdução de competências BIM em um escopo limitado de soluções de engenharia, o impacto na maturidade BIM do currículo é significativo.

Resumen Introducción. La red de movilización de ganado bovino para engorda en México es compleja. El motivo, volumen, origen y destino de los animales movilizados, determinan la estructura económica y red de mercado. Objetivo. Analizar la estructura de mercado de la red nacional de bovinos para engorda en México de 2017 a 2021. Materiales y métodos. El estudio consideró todas las cabezas de ganado movilizado para engorda en 956 municipios de origen (oferta) y 1173 municipios de destino (demanda) dentro de México del año 2017 a 2021. La estructura del mercado se analizó con medidas económicas, de densidad y centralidad del Análisis de Redes Sociales (ARS). Resultados. La red de movilización de bovinos para engorda se conformó con 31 orígenes y 32 destinos, un promedio anual de 3,9 millones de cabezas de ganado bovino movilizadas y 73,6 cabezas de ganado por movilización. Los Estados más importantes en la movilización de ganado, en origen y destino, fueron Chiapas y Durango. En todos los orígenes y destinos del ganado se encontró una alta concentración de novillo para engorda, porque tuvieron medidas de centralidad y densidad bajas de toda la red. Tanto en origen como en destino Veracruz y Durango fueron los más influyentes. Conclusiones. La red de mercado de bovinos para engorda en México tiene una estructura con alta densidad y baja centralidad. El grado de especialización, tanto de orígenes y destinos, es bajo. La oferta se concentra en el sureste y la demanda en el norte y centro del país. Esta información permite establecer tres redes: prevención sanitaria, trazabilidad del ganado e información de mercados.

Abstract Introduction. The network of cattle mobilization for fattening in Mexico is complex. The purpose, volume, origin, and destination of the mobilized animals determine the economic structure and market network. Objective. To analyze the market structure of the national network of cattle for fattening in Mexico from 2017 to 2021. Materials and methods. The study considered all heads of cattle mobilized for fattening in 956 municipalities (supply) and 1173 destination municipalities (demand) within Mexico from 2017 to 2021. The market structure was analyzed using economic, density, and centrality measures from Social Network Analysis (SNA). Results. The network of cattle mobilization for fattening was composed of 31 sources and 32 destinations, with an average annual mobilization of of 3.9 million heads of cattle and 73.6 heads of cattle per mobilization. The most important states in cattle mobilization, both in origin and destination, were Chiapas and Durango. In all cattle sources and destinations, there was a high concentration of fattening steers, as they had low centrality and density measures throughout the network. Veracruz and Durango were the most influential both in origin and destination. Conclusions. The cattle fattening market network in Mexico has a structure with high density and low centrality. The degree of specialization, both in sources and destinations, is low. Supply is concentrated in the southeast, while demand is concentrated in the north and center of the country. This information allows the establishment of three networks: sanitary prevention, cattle traceability, and market information.

Abstract During the last decades in Puno, Peru, the problem of contamination has worsened due to the combined action of the disorderly growth of the urban population, poor management of solid waste, discharge of untreated sewage into the bay of Lake Titicaca and practices of inadequate sanitation and hygiene, severely affecting the environment and human health. The objective of the study was to characterize the pro-environmental attitudes and behaviors of the city’s population of Puno in relation to sanitation, pollution and environmental management. The research is nonexperimental, quantitative, cross-sectional, descriptive, correlational and micro level of analysis. The universe of study was the population over 18 years of age in the urban area, which comprises 97,264 inhabitants; the sample, determined at simple random, was 382 people. A structured questionnaire was applied. Descriptive and inferential analysis and hypothesis testing were performed with SPSS statistical software. The results indicate that the environmental attitudes of the majority of the population are positive regarding factors and sources of pollution and effects on human health. On the contrary, environmental practices are inadequate in environmental management in the home and health and hygiene conditions in the home. It is concluded that the sustainable improvement of pro-environmental attitudes and behaviors demands a new public policy of environmental education, whose implementation incorporates the effective participation of civil society based on an incentive system.

Resumen Durante las últimas décadas en Puno, Perú, la problemática de la contaminación se fue agudizando por la acción combinada del crecimiento desordenado de la población urbana, gestión deficiente de residuos sólidos, descarga de aguas servidas sin tratamiento en la bahía del lago Titicaca y prácticas de sanidad e higiene inadecuadas; situaciones que afectan severamente el ambiente y la salud humana. El objetivo del estudio fue caracterizar las actitudes y comportamientos proambientales de la población de la ciudad de Puno en relación al saneamiento, la contaminación y la gestión ambiental. La investigación es no experimental, cuantitativa, trans¬versal, descriptiva, correlacional y nivel de análisis micro. El universo de estudio fue la población mayor de 18 años del área urbana, que comprende 97.264 habitantes; la muestra, deter¬minada al azar simple, fue de 382 personas. Se aplicó un cuestionario estructurado. El análisis descriptivo, inferencial y prueba de hipótesis se realizó con el software estadístico SPSS. Los resultados señalan que las actitudes ambientales de la mayoría de la población son positivas respecto a factores y fuentes de contaminación y efectos en la salud humana; contrariamente, las prácticas ambientales son inadecuadas en gestión ambiental en el hogar y condiciones de sanidad e higiene en la vivienda. Se concluye, que la mejora sostenible de actitudes y comportamientos proambientales, demanda de una nueva política pública de educación ambiental, cuya implementación incorpore la participación efectiva de la sociedad civil con base a un sistema de incentivos.

Abstract There is a growing interest in reducing energy consumption in the economic sectors, where the residential sector is a substantial consumer of energy in societies and therefore, a focus of attention for efficiency and renewable energy generation policies. In Ecuador, residential consumption represents 1/4 of the total electricity demanded by the socioeconomic system. Household composition has changed due to demographic dynamics, socioeconomic improvements and social justice efforts, which impacts electricity consumption. The aim of this study is to analyze the dynamics of energy consumption in Ecuador´s residential sector based on the construction of household typologies under the hierarchy of demographic, geographic, economic and technical variables using a top-down and bottom-up methodology and the application of MuSIASEM for which statistical information from National Surveys and Censuses was used, which allowed the construction of household typologies and their consumption pattern. The results show heterogeneous electricity consumptions in the 4.5 million households in 2017 hierarchically divided into 240 typologies. The pattern varies from the lowest consumption households with 50 KWh/month to the highest consumption of 350 KWh/month. For example, in the urban area the highest rate is concentrated in households made up of more than 8 people with rates between 150 to 180 KWh/month, while in the rural area the values range from 90 to 120 KWh/month but differ by geographic location and male or female headship. Likewise, the data allowed scaling to aggregate levels where it is shown that, of the total annual electricity consumption of 6,428 GWh, 54% of the consumption was concentrated in the coastal region, which concentrates 51% of the total households in the residential sector of Ecuador.

Resumen Existe un interés creciente por reducir el consumo de energía en los sectores económicos, donde el sector residencial es un consumidor sustancial de energía en las sociedades y por tanto, un foco de atención para las políticas de eficiencia y de generación energética renovable. En Ecuador, el consumo residencial representa un 1/4 del total de electricidad que demanda el sistema socioeconómico. La conformación de los hogares ha cambiado por la dinámica demográfica, mejoras socioeconómicas y los esfuerzos por la justicia social, lo cual impacta en el consumo de electricidad. El objetivo del estudio es analizar la dinámica del consumo de energía en el sector residencial del Ecuador a partir de la construcción de tipologías de hogares bajo la jerarquización de variables demográficas, geográficas, económicas y técnicas utilizando una metodología top-down y bottom-up y la aplicación de MuSIASEM para lo cual se utilizó información estadística de Encuestas y Censos Nacionales, que permitió construir las tipologías de hogares y su patrón de consumo. Los resultados muestran consumos de electricidad heterogéneos en los 4,5 millones de hogares presentes en 2017 divididos jerárquicamente en 240 tipologías. El patrón varía desde los hogares de menor consumo con 50 KWh/mes hasta los de mayor consumo de 350 KWh/mes. Por ejemplo, en la zona urbana la mayor tasa se concentra en los hogares conformados por más de 8 personas con tasas entre 150 a 180 KWh/mes, mientras que en la zona rural los valores oscilan entre 90 a 120 KWh/mes, pero difieren por ubicación geográfica y por su jefatura masculina o femenina. Igualmente, los datos permitieron escalar a niveles agregados donde se muestra que, del total de consumo anual de electricidad de 6,428 GWh, el 54% del consumo se concentró en la región Costa que concentra el 51% del total de hogares del sector residencial del Ecuador.

Abstract The increase in world population and the demand for technologies have exponentially increased the consumption of mineral resources, putting their availability for future generations at risk. The objective of this study is to know the state of academic production on resource scarcity and evaluate its consequences on exploitation, sustainability and technological development. A systematized bibliographic review was developed using the Scopus, WoS and SciELO databases. 57 documents were analyzed that cover topics such as the environmental impact of extraction, reuse strategies, criticality evaluations and regulatory policies for mining activity. It is concluded that the main factors of resource scarcity are related to the lack of regulations, the growing demand for new technologies and discrepancy in criticality estimation methods. There is a need to look for extraction alternatives and promote material recovery strategies.

Resumen El incremento de la población mundial y la demanda de tecnologías han aumentado de manera exponencial el consumo de recursos minerales, poniendo en riesgo su disponibilidad para las generaciones futuras. El presente estudio tiene como objetivo conocer el estado de la producción académica sobre la escasez de recursos y evaluar sus consecuencias en la explotación, la sostenibilidad y el desarrollo tecnológico. Se llevó a cabo una revisión bibliográfica sistematizada usando las bases de datos Scopus, WoS y SciELO. Se analizaron 57 documentos que abordan temáticas como el impacto ambiental de la extracción, estrategias de reutilización, evaluaciones de criticidad y políticas de regulación de la actividad minera. Se concluye que los principales factores de la escasez de recursos están relacionados con la falta de normativa, la creciente demanda de nuevas tecnologías y discrepancia en los métodos de estimación de criticidad. Se advierte la necesidad de buscar alternativas de extracción y fomentar estrategias de recuperación de materiales.

Abstract: This research proposes two models for the problem of short-term economic dispatch of electrical power systems through nonlinear programming (NLP). The problems raised will be resolved through the cost function of the classic economic dispatch where thermal and hydraulic generation plants will be considered to obtain the electrical power generated in each of the nodes. The proposed methodology will be used for a short-term period of 24 hours with different hourly demand, as it is a short-term dispatch, it focuses on the delivery of power that covers the designated demand in each schedule, so it will not consider a deficit cost or uncertainty in the variables in any of the cases. In the first instance, the model will be developed for a single node with cascade reservoirs, while the second case will be developed in the IEEE 14-bus system. The non-linear programming shows satisfactory results, complying with the operational restrictions implemented in the mathematical model, in addition, the participation of thermal generation is considerably reduced, which represents a lower cost. The first model of a node is validated through bibliography, obtaining an operating cost of $904,990. In the same way, complying with all the designated parameters, the second model obtains a total cost of $129,800, satisfying the total demand in both cases, subject to each of its restrictions.

Resumen: La presente investigación propone dos modelos al problema de despacho económico a corto plazo de los sistemas eléctricos de potencia por medio de la programación no lineal (PNL). Los problemas planteados serán resueltos mediante la función de costo del despacho económico clásico en donde se considerarán centrales de generación térmica e hidráulicas para obtención de la potencia eléctrica generada en cada uno de los nodos, la metodología propuesta será utilizada para un periodo a corto plazo de 24 horas con diferente demanda horaria, al ser un despacho a corto plazo este se enfoca en la entrega de potencia que cubra la demanda designada en cada horario, por lo que no considerará para ninguno de los casos un costo de déficit o incertidumbre en las variables. En primera instancia se desarrollará el modelo para un solo nodo con embalses en cascada, mientras que el segundo caso será desarrollado en el sistema de 14 buses de la IEEE. La programación no lineal muestra resultados satisfactorios cumpliendo con las restricciones operativas implementadas en el modelo matemático, además se reduce considerablemente la participación de generación térmica lo que representa menor costo, el primer modelo de un nodo es validado mediante bibliografía obteniendo un costo de operación de $904.990. De la misma forma, cumpliendo con todos los parámetros designados, el segundo modelo llega a obtener un costo total de $129.802,16 satisfaciendo el total de la demanda en ambos casos, sujeto a cada una de sus restricciones.

Resumo Este artigo aborda a questão da habitação e dos aglomerados subnormais no contexto de municípios selecionados da Região Metropolitana do Rio de Janeiro, Brasil, e verifica a viabilidade de cumprimento da meta 11.1 dos objetivos de desenvolvimento sustentável (ODS) em escala regional. São utilizados como fontes de dados, estudos recentes encomendados e divulgados pelo Governo Federal Brasileiro e dados do Censo. Na realidade estudada, o município de Belford Roxo, com índices alarmantes de comunidades e domicílios em contexto de aglomerados subnormais, apresenta tendência de deterioração da situação da habitação. Japeri e Queimados, pelas taxas de crescimento demográfico das últimas décadas, também merecem ser monitorados. Enquanto Nova Iguaçu, Mesquita e Nilópolis, com percentuais menores de suas populações vivendo em aglomerados subnormais, apresentam condições propícias para o alcançar a meta 11.1 dos ODS até 2030.

Abstract This article addresses the issue of housing and subnormal agglomerations in selected municipalities within the Metropolitan Region of Rio de Janeiro, Brazil, and verifies the feasibility of achieving target 11.1 of the Sustainable Development Goals (SDGs) on a regional scale. Recent studies commissioned and released by the Brazilian Federal Government and Census data are used as data sources. In the reality studied, the municipality of Belford Roxo, with alarming rates of communities and households in the context of subnormal agglomerations, shows a tendency to deteriorate the housing situation. Japeri and Queimados, due to the demographic growth rates of recent decades. Conversely, Nova Iguaçu, Mesquita, and Nilópolis, with smaller proportions of their populations living in subnormal agglomerations, present a favorable condition for achieving target 11.1 of the SDGs by 2030.

Resumen Este artículo aborda el tema de la vivienda y de las aglomeraciones subnormales en el contexto de municipios seleccionados de la Región Metropolitana de Río de Janeiro - Brasil, y verifica la viabilidad de alcanzar la meta 11.1 de los objetivos de desarrollo sostenible (ODS) a escala regional. Los estudios recientes encargados y publicados por el gobierno federal brasileño y los datos del censo se utilizan como fuentes de datos. En la realidad estudiada, el municipio de Belford Roxo, con índices alarmantes de comunidades y viviendas en el contexto de aglomeraciones subnormales, muestra una tendencia al deterioro de la situación habitacional. Japeri y Queimados, debido a las tasas de crecimiento demográfico de las últimas décadas, también merecen ser monitoreadas, mientras que Nova Iguaçu, Mesquita y Nilópolis, con porciones más pequeñas de sus poblaciones viviendo en aglomeraciones subnormales, presentan una condición favorable para alcanzar la meta 11.1 de los ODS para 2030.

Abstract: Corn drying reduces the moisture content present in the grain to levels that allow safe storage. This process requires a large amount of energy, which is why, if not applied correctly, it can affect the quality of the product to be dried, in addition to representing important costs in the operation of the drying plants. The objective of this research is to analyze the corn drying systems used in Canton Quevedo, Province of Los Ríos. In order to achieve the objective, field visits were made to the area under study, considering factors related to the technology used and the corn harvesting period, as well as, characteristics of the coastal region of Ecuador. It was determined that stationary or fixed bed drying is the drying system widely used for corn drying, which uses subsidized liquefied petroleum gas as fuel for its operation. The moisture content of the corn received at the drying plants is above 30% in the two harvesting periods of the product, a situation that has an impact on processing times and product quality. The fuel demand for drying an average mass of product of 60.2 tons, between the first harvest period, March - June, and the second period, September - November, presents a difference of 300.77 kg of LPG in relation to the first harvest, being the moisture content a key factor to take into account.

Resumen: El secado del maíz permite reducir el contenido de humedad presente en el grano a niveles que permitan un almacenamiento seguro. El objetivo de esta investigación permite analizar los sistemas de secado de maíz empleados en el Cantón Quevedo, Provincia de Los Ríos. Para alcanzar nuestro objetivo se realizaron visitas de campo en la zona objeto de estudio, por lo que se consideraron factores relacionados con la tecnología empleada y período de cosecha de maíz, características de la región costera del Ecuador. Se determinó que el secado estacionario o de lecho fijo es el sistema de secado ampliamente empleado para el secado de maíz, el cual emplea como combustible el gas licuado de petróleo subsidiado para su funcionamiento. La humedad de recibo de maíz en las plantas de secado presenta niveles de humedad por encima del 30 %, en los dos periodos de cosecha del producto, situación que repercute en los tiempos de proceso y en la calidad del producto. La demanda de combustible para secar una masa promedio de producto, 60,2 Ton, entre el primer período de cosecha que va de Marzo - Junio, y el segundo período, Septiembre - Noviembre, presenta una diferencia de 300,77 Kg de GLP con relación a la primera cosecha, siendo la humedad de recibo un factor clave a tomar en cuenta.

ABSTRACT Food availability is defined as the sufficient quantity of food of adequate quality and culturally acceptable for the population of a country in a given period. In the case of the cities of the North Coast of the Uruguay River, there is little availability in terms of local fishing. The objectives of this research were to analyze the causes of this scarce availability through the opinion of the artisanal fishermen of the region, and the referring institutions. Semi-structured interviews were conducted with artisanal fishermen and institutional references in the region, as well as a representative of the private sector. The inability of fishermen to dedicate themselves exclusively to the activity; the export destination that has the majority of the region's catches; the low consumption at national level and the scarce demand of the cities for river fish, were some of the enunciated causes.

RESUMEN La disponibilidad de alimentos se define como la cantidad suficiente de alimentos de calidad adecuada y culturalmente aceptables para la población de un país en un período determinado. En el caso de las ciudades del Litoral Norte del Río Uruguay, se observa una escasa disponibilidad en materia de pesca local. Los objetivos de esta investigación fueron analizar las causas de esta escasa disponibilidad a través de la opinión de los y las pescadores artesanales de la región, y las instituciones referentes. Se realizaron entrevistas semi estructuradas a pescadores artesanales y referentes institucionales de la región, así como a un representante del sector privado. La imposibilidad de los pescadores para dedicarse exclusivamente a la actividad; el destino exportador que tiene la mayoría de las capturas de la región; el bajo consumo a nivel nacional y la escasa demanda de las ciudades por pescado de río, fueron algunas de las causas enunciadas.

Abstract The present research work shows the optimal energy management of an isolated microgrid based on nonconventional renewable energy sources. For which an economic dispatch problem is proposed that seeks to supply the electrical demand at the lowest posible operating cost, based on a mixed integer nonlinear optimization problem. The nonlinearity of the algorithm is presented by including the characteristic equation of the real operation of the generating set in the optimization model. The input data to the economic office such as solar radiation and wind speed were obtained from the NASA platform located on Santa Cruz Island, Galapagos province, Ecuador. In addition, the electricity demand data was obtained from real measurements of the sector. The economic dispatch problem has been determined for 12, 24 and 168 hours respectively, obtaining a proportional energy distribution for each case of 50.40% supplied by the photovoltaic generator, 23.92% by the diesel generator, 17.14% by the battery bank and 5.53% by the wind generator, so the demand was supplied in its entirety, meeting the objective that the generating set does not present intermittencies and obtaining the lowest operating cost of the system.

Resumen El presente trabajo de investigación muestra la gestión óptima de la energía de una microrred aislada basada en fuentes de energía renovable no convencional. Para lo cual se plantea un problema de despacho económico que busca abastecer la demanda eléctrica al menor costo de operación posible, a partir de un problema de optimización no lineal entero mixto. La no linealidad del algoritmo se presenta al incluir la ecuación característica del funcionamiento real del grupo electrógeno en el modelo de optimización. Los datos de entrada al despacho económico como radiación solar y velocidad del viento fueron obtenidos de la plataforma de la NASA situada sobre la isla Santa Cruz, provincia de Galápagos, Ecuador. Además, los datos de la demanda eléctrica fueron obtenidos de mediciones reales del sector. El problema de despacho económico se ha resultado para 12, 24 y 168 horas respectivamente, obteniendo una distribución energética proporcional para cada caso del 50.40 % suministrada por el generador fotovoltaico, 23.92 % por el generador diésel, 17.14 % por el banco de baterías y 5.53 % por el generador eólico, por lo que la demanda fue abastecida en su totalidad cumpliendo con el objetivo de que el grupo electrógeno no presente intermitencias y obteniendo el menor costo de operación del sistema.

Abstract Information and Communications Technologies (ICT) have followed a trajectory of systematic and accelerated development, marking transformations in various sectors of society. In this dynamic context, higher education institutions face the imperative to adapt and evolve in a coherent and strategic manner in response to technological, scientific-technical and methodological progress. Recognition of levels of integration in postgraduate training processes and these technologies is required. From this perspective, the general objective was proposed to describe advanced experiences based on pedagogical experiences in Graduate Education at the Graduate Faculty of the Technical University of Manabí (UTM). A descriptive, transversal methodology with a non-experimental design was used, with various scientific methods, such as documentary, analytical-synthetic, systematization, unstructured interviews and case studies. The reality of the postgraduate programs in the Graduate Faculty of the UTM was analyzed, with the use of ICT, and in correspondence the emergence of strategies aimed at updating teachers was expressed. Various authors were consulted with studies related to the use of virtual environments and the online modality in the 4th level, and it was possible to see that the trend is to increase this modality in the programs and thus makes them more competitive and with greater demand.

Resumen Las Tecnologías de la Información y las Comunicaciones (TIC) han seguido una trayectoria de desarrollo sistemático y acelerado, marcando transformaciones en diversos sectores de la sociedad. En este contexto dinámico, las instituciones de educación superior enfrentan el imperativo de adaptarse y evolucionar de manera coherente y estratégica en respuesta al progreso tecnológico, científico-técnico y metodológico. Se exige del reconocimiento de niveles de integración en los procesos de formación de posgrado y estas tecnologías. Desde esta perspectiva se planteó como objetivo general, describir experiencias de avanzada en función de las vivencias pedagógicas en la Educación de Posgrado en la Facultad de Postgrado de la Universidad Técnica de Manabí (UTM). Se utilizó una metodología de tipo descriptiva, transversal y con diseño no experimental, con diversos métodos científicos, como el estudio documental, analítico-sintético, sistematización, entrevista no estructurada y estudio de caso. Se analizó la realidad de los programas de posgrado en la Facultad de Posgrado de la UTM, con el empleo de las TIC, y en correspondencia se expresó la emergencia de estrategias orientadas a la actualización de los docentes. Se consultaron diversos autores con estudios relacionados con el empleo de ambientes virtuales y la modalidad en línea en el 4to nivel, y se pudo apreciar, que la tendencia es al aumento de esta modalidad en los programas y así los hace más competitivos y con mayor demanda.

Introdução: O ensino em cirurgia convencional foi tradicionalmente baseado no modelo halstediano do “see one, do one and teach one” (veja um, faça um e ensine um); porém, com a bem sucedida propagação da cirurgia videolaparoscópica precisou ser adaptado para um novo modelo do “do many, mentored always” (fazer vários, sempre supervisionado). A nova era da cirurgia demanda treinamento sequencial, com crescente complexidade e repetição supervisionada para adquirir habilidades especificas prévias ao primeiro ato operatório. Objetivo: Desenvolver modelo para ensino e treinamento em videocirurgia com plataforma de baixo custo, fácil execução e baixa fidelidade com tarefas que utilizam materiais sintéticos. Método: Construiu-se com materiais de baixo custo plataforma utilizando apenas placa de madeira, poucos materiais de ferragem (parafuso simples, parafuso com porca tipo borboleta, gancho com rosca), folha de EVA (etileno acetato de vinila), tinta branca para artesanato e caneta hidrográfica. A amostra-teste foi composta por 15 cirurgiões gerais com mais de 10 anos de experiência em videolaparoscopia. Iniciou-se a avaliação com um vídeo explicativo com duração de 20 min. A seguir, cada cirurgião executou 5 tarefas gravadas para posterior análise e pontuação. Mediu-se as habilidades de acordo com a pontuação. Resultados: A plataforma foi útil e eficaz em reproduzir as atividades utilizadas para replicação do programa comparativo do Fundaments of Laparoscopic Surgery. A amostra de cirurgiões atingiu o tempo alvo definido como padrão pelo programa. Conclusão: A plataforma elaborada com materiais de baixo custo é de fácil aquisição, mostrou-se modelo eficaz para treinamento em videocirurgia, de fácil replicabilidade e construção, adaptável a vários modelos de tarefas, e feita com materiais sintéticos.

Introduction: Teaching in conventional surgery has traditionally been based on the Halstedian model of “see one, do one, and teach one”. However, with the widespread success of videolaparoscopic surgery, the teaching method needed to be adapted to a novel “Do many, always mentored” model. The modern era of surgery demands sequential training with progressively increasing complexity and supervised repetition, in order to acquire specific skills prior to the first surgical procedure. Objective: To develop a new experimental teaching and training with low cost and low fidelity platform for laparoscopic surgery using synthetic materials, and simple manufacturing. Method: A platform was built using low-cost materials easily found in hardware stores, consisting of a wooden board and a few hardware materials (threaded bolt, wing nut and bolt, threaded hooks), EVA sheet (ethylene vinylacetat), white crafting paint, and felt-tip pen. The sample consisted of 15 general surgeons with more than 10 years of experience in videolaparoscopy. The evaluation began with an explanatory video lasting 20 min. Next, each surgeon performed 5 recorded tasks for later analysis and scoring. Skills were measured according to the stablished score. Results: The developed platform was useful and capable of reproducing the tasks performed based on the program of Fundaments of Laparoscopic Surgery. All the surgeons of the sample group achieved the target time proposed for the program. Conclusion: Was shown that the proposed platform can be built using easily obtainable and low-cost materials, and it proved to be an effective model for training in laparoscopic surgery, being easy to replicate and construct. Additionally, this platform can be easily adapted to various models of tasks using materials similar to those found in other training programs, that are widely practiced and have been globally validated.

RESUMEN Introducción: La pandemia del COVID-19 ha provocado cambios que afectan a los sistemas sanitarios y al enfoque de las enfermedades infecciosas en todo el mundo. La demanda de vacunas contra el COVID-19 se encuadra en un espectro que va desde el rechazo hasta la demanda, con una aceptación pasiva en el medio. Objetivo: Determinar la adherencia de los adultos a la vacunación contra la COVID-19. Chauria-Caballero, Paraguay 2022. Metodología: Estudio observacional, descriptivo, de corte transversal, con enfoque cuantitativo. El muestreo fue no probabilístico por conveniencia. La muestra estuvo conformada por un total de 225 adultos; los datos fueron recabados por medio de una encuesta elaborada por la investigadora, los datos fueron procesados con el software EPI INFO. Resultados: La mayoría de los sujetos de estudio se vacunaron, y hubo adherencia de la población a la vacuna contra la COVID-19 en un 93 %; diversos factores influyeron en las decisiones de estos; el porcentaje de adultos no vacunados mencionan como motivos su desconfianza (69 %) y el miedo/temor a la vacunación (31 %). Discusión: El estudio encontró una alta adherencia en general, la gran mayoría de los participantes vacunados contra COVID-19, porcentajes significativos se reportaron en Chile, China y Catar, cifras muy altas con relación a la aceptación de la vacuna a nivel país, teniendo una cobertura con un porcentaje mayor a la mitad con al menos una dosis.

ABSTRACT Introduction: The coronavirus disease (COVID-19) pandemic has caused changes that affect health systems and the approach to infectious diseases worldwide. The demand for COVID-19 vaccines falls on a spectrum from rejection to demand, with passive acceptance in between. Objective: To determine the adherence of adults to vaccination against COVID-19. Chauria-Caballero, Paraguay 2022. Methods: This was an observational, descriptive, cross-sectional study using a quantitative approach. For convenience, the sampling was non-probabilistic. The sample comprised of 225 adults. The data were collected through a survey elaborated by the researcher, and the data were processed using EPI INFO software. Results: The majority of the study subjects were vaccinated, and there was 93% adherence of the population to the COVID-19 vaccine. Various factors influenced their decisions; the percentage of unvaccinated adults mentioned their distrust (69%) and fear of vaccination (31%). Discussion: The study found high adherence in general, the vast majority of participants were vaccinated against COVID-19, with significant percentages reported in Chile, China, and Qatar, very high figures in relation to the acceptance of the vaccine at the country level, with coverage of more than half with at least one dose.