Resumo: Um desafio bem conhecido é prever as transformações que ocorrem durante a soldagem das ligas metálicas com o objetivo de controlar as propriedades da solda. Desta forma, este estudo apresenta um modelo Termo-Mecânico-Metalúrgico para predizer numericamente a história térmica, as transformações de fase no estado sólido, a microestrutura de solidificação e a distribuição de dureza durante e após a soldagem de aços de alta resistência e baixa liga. O modelo foi implementado numericamente em um código computacional próprio baseado no Método dos Volumes Finitos, o que permitiu rastrear e calcular dinamicamente as frações volumétricas de ferrita, perlita, bainita e martensita na zona afetada pelo calor, além da formação e determinação do espaçamento do braço dendrítico na zona de fusão, enquanto que a distribuição da dureza na zona afetada pelo calor foi calculada aplicando-se a regra da mistura de fases. Para tanto, soldas autógenas usando o processo Gas Tungsten Arc Welding de passe único foram simuladas numericamente e experimentalmente realizadas em amostras do aço de alta resistência e baixa liga AISI 4130, incluindo seu pré-aquecimento com o objetivo de avaliar a eficácia do modelo proposto para simular a soldagem de peças em diferentes condições térmicas iniciais, tendo sido obtida uma estreita concordância entre os resultados calculados e experimentais.

Abstract: A well-known challenge is to predict the transformations occurring during the metal alloys welding aiming to control the weldment properties. Thus, this study presents a Thermo-Mechanical-Metallurgical model to numerically predict the thermal history, the solid-state phase transformations, the solidification microstructure and the hardness distribution during and after the welding of high strength low-alloy steels. The model was numerically implemented in an in-house computational code based on the Finite Volume Method, which allowed to dynamically track and calculate the volume fractions of ferrite, pearlite, bainite and martensite at the heat-affected zone, besides the formation and determination of dendrite arm spacing at the fusion zone, whereas the hardness distribution at the heat-affected zone was calculated by applying the phase mixture rule. For this, single-pass autogenous Gas Tungsten Arc Welding welds were numerically simulated and experimentally carried out on high strength low-alloy AISI 4130 steel samples, including their preheating to evaluate the effectiveness of the proposed model to simulate the workpieces welding in different initial thermal conditions and a close agreement between the calculated and experimental results were obtained.

This work aimed to analyze the damage behavior of cold rolled TRIP780 steel sheet submitted to interrupted uniaxial tensile tests performed along the rolling direction. The formation of voids is investigated as a function of the straining level using digital image analysis of scanning electron micrographs to obtain the measures of void density, void area fraction, void aspect ratio and mean void size. The volume fractions of both ferrite/martensite and retained austenite constituents were obtained from X-ray diffraction measurements. An abruptly decrease of retained austenite was observed at early stages of deformation followed by a slow saturation. The resulting strain-induced martensite is responsible for improving the formability of the TRIP780 as observed by instantaneous strain-hardening exponent. In the lower strain range, growth and coalescence of existing microvoids prevailed at both in-plane directions whereas nucleation of microvoids was also observed along the loading direction. Conversely, nucleation prevailed at the transverse direction in the intermediate strain range whereas growth and coalescence were predominant aligned to the loading direction. At larger strain levels, growth and coalescence of microvoids prevailed at both directions. The microvoids were initially found around inclusions and at the interface of ferrite-martensite phases and lastly also at the ferrite matrix.

The microstructural alterations suffered during the process of drawing deformation and subsequent annealing of pearlitic steel wires, were evaluated by scanning electron microscopy and atomic force microscopy. The deformed material showed the curling structure in cross section while, in the longitudinal section, the lamellae was aligned with the drawing direction. The microstructural characterization of deformed samples also allowed observing an interlamellar spacing reduction and the intermediate lamellae alignment process. After the heat treatment at 1000ºC for 5 min the microstructure was restored, however, few recrystallized grains were observed. The recovery was the dominant phenomenon, due to factors associated with curling structure that inhibited recrystallization.