Samplers based on the diffusive gradients in thin films for organics (o-DGT) were developed and applied in Brazilian aqueous matrices for the determination of four emerging contaminants (EC): 4-octylphenol, 4-nonylphenol, triclosan, and bisphenol A. The OASIS HLB resin used as the binding phase presented a high sorption capacity and the extraction associated with sonication, using a mixture of acetonitrile and methanol (2:1, v v-1) as the solvent, provided a higher desorbed mass of the compounds. The diffusion coefficients determined experimentally were in the range of the values found in the literature and the pH and ionic strength influenced the sorption of some compounds by the binding phase. The substances were detected and quantified in tap and river water samples after 7 days of deployment using gas chromatography tandem mass spectrometry (GC-MS/MS). Finally, the results indicate deficiencies in the current wastewater, as well as water treatment systems, and could contribute in the future to the improvement of public policies on basic sanitation in Brazil.

ABSTRACT The combination of pillarization and charge neutralization with Li+ can make montmorillonite an important support material for industry and decontamination of pollutants in soil and water. Montmorillonite characterization techniques were described in detail, and pillarization procedures were used, after Li+ saturation, to modify and manipulate the chemical and mineralogical surface properties of this montmorillonite. Eight samples were produced: 1) natural montmorillonite (Chisholm Mine - MMT); 2) Li+ saturated montmorillonite (MMTLi); 3) polyethylene glycol (PEG) Al-pillared montmorillonite (AlPEG); 4) PEG Al-pillared montmorillonite saturated with Li (AlPEGLi); 5) Al-pillared montmorillonite with 14 h contact time (Al14h); 6) Al-pillared montmorillonite Al14h saturated with Li (Al14hLi); 7) Al-pillared montmorillonite with 0 h contact time (Al0h); and 8) Al-pillared montmorillonite Al0h saturated with Li (Al0hLi). The natural sample was identified as interlayered montmorillonite composed of chlorite layers or with a high degree of Al-hydroxy filling. Concerning the total permanent charges, 70 % occurred by isomorphic substitution of Al3+ by Mg2+ in octahedral layer and 30 % of Si4+ by Al3+ in tetrahedral layer. The pillarization method using the PEG produced a small number of stable pillars. The new milder pillarization method (Al0h) did not cause damage in the formation of Al-hydroxy. In this method, the resulting pillars were more homogeneous in size. Thereby, the Al0h Li method has been shown to produce a supporting material with a constant interlayer spacing, increased of the specific surface area (SSA), and drastic reduction of the cation exchange capacity (CEC) as compared to MMT. This modified mineral can be used in, for example, decontamination of polluted water with nonionic organic pollutants.

Abstract A new low-cost material is presented for the first time, aiming to study the sorption process for the stir-bar sorptive extraction (SBSE) technique. The bars were made using a composition of a commercial epoxy resin and montmorillonite, under different compositions and a final ratio of 70% (epoxy) and 30% (montmorillonite) was employed, providing the best mechanical and chemical resistance. A PTFE support was developed to hold the bars permitting the magnetic stirring, without turbulent behavior even under long times of stirring at 1000 rpm. The bars were employed to study the sorption of the herbicide atrazine (ATZ), and the best extraction conditions were: sample volume 20.0 mL, pH 6.0, extraction time of 15 min, room temperature, stirring speed of 100 rpm, and 10.0% (w v-1) NaCl. This preliminary evaluation suggests that the modified bars could be employed for ATZ sorption, affording close to 71% of ATZ removal, and presented robust characteristics to be used at least 80 times.

Soils that had received successive applications of retorted oil shale (ROS) in an experiment under field conditions were used in this study, aiming to evaluate the availability of trace elements. In the batch tests, we observed that toxic elements present in the ROS are not desorbed from the matrix in significant amounts to contaminate soil and groundwater. The element Ca represents the greatest nutrient contribution, which has high mobility and ease release into the soil solution. Concerning the results obtained from the soil extracts analysis; we observed that the undesirable elements released into the extracts are not directly related to the presence of ROS in the soil samples. Comparing the behavior of soil samples with and without ROS it is possible to infer that many of the trace elements are derived from soil constituents, from previous fertilizer and pesticides applications. The study suggested that the ROS can be used as a soil conditioner for agricultural purposes without adding harmful elements to the environment.

A pyrolyzed oil shale by-product known as retorted shale was functionalized with HCl, HNO3, H2SO4, H3PO4, HNO3/H2SO4 (3:1), Fenton's reagent, (NH4)2S2O7, NaOH, and KMnO4 using either ultrasound (Route 1) or reflux (Route 2). The products obtained were evaluated in terms of cation exchange capacity (CEC). Structural characterization was performed using X-ray diffraction, X-ray fluorescence, and infrared spectroscopy to identify the functional groups present. The best results were achieved using Route 2 with solutions of either H3PO4 or HNO3/H2SO4 (3:1), giving CEC values of 315 and 316 mmolc kg-1, respectively. The pyrolyzed oil shale functionalized using Route 2 (reflux) with NaOH as the activating agent showed the highest sorption of methylene blue (35.6 mg g-1). The main mechanisms observed for oil shale by-product functionalization were oxidation, nitration, and CaO leaching.

The main objective of the present work was to validate a chromatographic method to determine herbicides commonly applied in the irrigated rice farming. For this, matrix-matched calibration was employed along with the extraction and clean-up of the samples by quick, easy, cheap, effective, rugged and safe (QuEChERS) method and determination of the analytes by high performance liquid chromatography tandem mass spectrometry (LC-MS/MS) with electrospray ionization in the positive mode. By this method, it was possible to achieve the ionization and detection of a total of 18 herbicides, with quantification of 12 of them. The method presented adequate precision and accuracy according to the European Commission and the International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH) guidelines for analytes in low concentrations. The limits of quantification ranged from 0.015 μg g-1 for oxadiazon to 0.165 μg g-1 for imazapyr. The method showed good linearity with R2> 0.99 and recovery values from 92 to 103%. The proposed protocol is adequate for monitoring bispyribac-sodium, cyclosulfamuron, cycloxydim, clomazone, ethoxysulfuron, fenoxaprop-p-ethyl, imazapic, imazapyr, imazethapyr, metsulfuron-methyl, oxadiazon and thiobencarb in rice grains in concentrations up to 109 times lower than the maximum residue limits established by the Brazilian Health Surveillance Agency (ANVISA) for these compounds in rice samples.

The use of MT-K10 Montmorillonite immobilized onto agarose was investigated in this work as an alternative binding phase in Diffusive Gradient in Thin Film (DGT) devices for the determination of metallic labile species. In addition, agarose itself was also used as the diffusive phase. The percentage of sorption of Zn2+, Cu2+, Cr3+, Mn2+, Cd2+, Pb2+, and Ni2+ onto the binding phase was higher than 80% and the desorption process for all elements was also greater than 75%. Elution factors were determined experimentally, ranging from 0.74 for Zn2+ and 0.90 for Cr3+ and Pb2+. The accumulation of all species was linear with time, in agreement with the Fick's 1st law of diffusion. The deployment of the alternative devices in natural waters was compared to commercial devices. Labile concentrations determined by the alternative devices were slightly superior compared to results obtained with the deployment of original DGT devices due to the less restrictive pores of agarose.

Neste trabalho foi proposto um procedimento para a extração do herbicida atrazina (AT) e dos principais metabólitos desetil-atrazina (DEA) e desisopropil-atrazina (DIA) de uma amostra de latossolo vermelho proveniente da região sudoeste do estado do Paraná no Brasil, onde a AT está entre os herbicidas mais amplamente utilizados. Foi conduzida uma comparação usando extração por agitação e por ultrassom, sendo obtido um procedimento de extração simples e rápido, seguido pela quantificação por cromatografia em fase líquida de alta eficiência. Cabe ressaltar que foi utilizado um estudo por planejamento fatorial, o qual foi decisivo para determinar as melhores condições de extração por agitação. Foram obtidos percentuais de recuperação e desvios padrão relativos adequados, para amostras de solo de três diferentes profundidades, o que sugere a possibilidade de empregar o método de extração proposto para a quantificação de AT, DEA e DIA em amostras de latossolo vermelho.

An optimization procedure for the extraction of the herbicide atrazine (AT), and the main degradation products deethylatrazine (DEA) and deisopropylatrazine (DIA) from an oxisol soil sample was carried out, for a soil from the Southwest of Paraná State in Brazil, where AT is among the most largely employed herbicide. A comparison between shaking and ultrasound extraction was performed, to define a simple and fast extraction procedure, followed by the quantification using high performance liquid chromatography. It is important to inform that a factorial planning was employed, that was very important to define the best conditions of extraction by shaking. Appropriate recovery values were observed using soil samples from three different depths, as well as the relative standard deviation, suggesting the possibility to employ the proposed extraction method for quantification of AT, DEA and DIA in oxisol samples.

Neste trabalho, propõe-se a determinação de fenol e o-cresol por análise por injeção em fluxo (FIA) com detecção espectrofotométrica, utilizando a reação com 4-aminoantipirina, a fim de quantificar essas espécies em extratos de solo. Após otimização das condições por planejamento fatorial, constatou-se uma maior frequência de amostragem em comparação com o método convencional, bem como valores de recuperação, limites de detecção e de quantificação comparáveis para ambos os métodos. Tais aspectos sugerem que esse método pode ser uma alternativa viável para a determinação de compostos fenólicos em extratos de solos.

Phenol and o-cresol determination by flow injection analysis (FIA) with spectrophotometric detection, employing the 4-aminoantipyrine reaction, is proposed in this work in order to quantify these species in soil extracts. The method was improved by a factorial planning, being verified a higher sampling rate in comparison with the conventional method, and recovery values, limits of detection and quantification similar for both methods. These aspects suggest this method as a feasible alternative for phenolic compound determinations in soil extracts.

The objective of the present study was to evaluate the adsorption of the herbicide Diuron onto smectite and Fe oxides minerals. Ninety mg of each mineral, 1 mL of 0.15 mol L-1 CaCl2 and 8 mL of Diuron (0.25-10.00 mg L-1) were used in triplicates. These materials were shaken, ultra centrifuged and the supernatant collected and analysed on a UV-Vis spectrophotometer. The Diuron presented low adsorption onto clay mineral fractions. Adsorption was greater onto Fe oxides at pH 7.0, possibly due to proximity to the point of zero charge of these minerals.

The clay minerals montmorillonite (MT) and vermiculite (VT), previously treated with Ca2+, K+ and Na+, were employed in a sorption study with herbicides. The herbicides 2,4-D, diuron, alachlor and metolachlor showed no interaction with MT and VT. On the other hand, the triazines presented a good sorption process, close to 100% for ametrine removal and near to 56 and 69% for atrazine and simazine, respectively, by MT. These results suggest that the MT specie may be a good material for triazines removal from aqueous medium and an alternative phase to preconcentration process, besides to exhibit a good selectivity.

The clay mineral montmorillonite-K10 (MT), treated under acidic medium and saturated with potassium ions (MTK), was employed in sorption and desorption studies aiming the preconcentration of Cr(III) and the speciation analysis of chromium. The sorption process of Cr(III) was close to 100%, suggesting that MTK was a good material for Cr(III) preconcentration, although, the maximum recovery in HNO3 solution was near 89%. On the other hand, Cr(VI) practically was not retained in MTK, suggesting this material as an appropriate mineral phase to be used in speciation analysis of chromium in aqueous medium.

Speciation of metals in a synthetic freshwater was comparatively evaluated using Anodic Stripping Voltammetry, Diffusive Gradients in Thin Films and a Chemical Equilibrium Model. The labile fractions of Cu and Zn quantified by DGT were similar to the ones measured by ASV. The labile species of Cd and Pb could not be determined by both experimental methods due to the formation of inert complexes with organic ligands in the sample. Despite the differences among the methods, the speciation results obtained by the use of DGT and ASV agreed well with predictions made by the chemical equilibrium model.

Proton binding properties of humic and fulvic acids were studied by potentiometric titration. Carboxylic groups were the predominant ionizable sites in comparison to phenolic and amine groups. Total acidity of fulvic acid was 12 x 10-3 mol g-1, a number significantly higher than that obtained for humic acid (5.2 x 10-3 mol g-1). Copper ion binding was evaluated at pH 4, 5 and 6 by potentiometric titration with an ion selective electrode for Cu(II). Differential stability constants and complexation capacities were systematically higher for humic acid, despite its lower number of ionizable sites in comparison with fulvic acid.

Este trabalho apresenta um sistema de injeção seqüencial associado a uma unidade de filtração tangencial e um detector na região do ultravioleta, para monitorização em linha da sorção de ácido fúlvico em duas vermiculitas modificadas. Com o sistema proposto foi possível melhorar a resolução temporal, na investigação do tempo de equilíbrio necessário para o sistema sorvente-soluto atingir o equilíbrio químico. A sorção em uma suspensão 10 g L-1 de vermiculita, modificada por intercalação com poliidroxicátions de Fe(III) foi rápida, atingindo o equilíbrio após 4 min de tempo de contato, resultando em sorção de 97,9 % do ácido fúlvico inicialmente presente em uma solução 10 mg L-1. A sorção na suspensão 10 g L-1 de vermiculita organofílica, obtida por troca iônica com brometo de hexadeciltrimetilamônio apresentou uma rápida taxa inicial de sorção, seguida por processos de dessorção e readsorção, atingindo o equilíbrio após 30 min de tempo de contato, com sorção de 98% do ácido fúlvico inicialmente presente em uma solução 10 mg L-1.

This paper presents a sequential injection system associated with a tangential filtration unit and an ultraviolet detector for on-line monitoring of fulvic acid sorption onto two modified vermiculites. With the proposed approach it was possible to improve the temporal resolution in the investigation of the equilibrium time needed for the system sorbent-sorbate to reach the chemical equilibrium. Sorption onto a 10 g L-1 suspension of vermiculite material modified by intercalation of polyhydroxycations of Fe(III) was fast, reaching the equilibrium after 4 min of contact time, and resulting in sorption of 97.9 % of the initial 10 mg L-1 fulvic acid concentration. Sorption onto a 10 g L-1 suspension of an organic vermiculite which was modified by ion exchange with hexadecyltrimethylammonium bromide exhibited a fast initial rate of sorption, followed by desorption and re-adsorption processes, reaching the equilibrium after 30 min of contact time, with sorption of 98% of the initial 10 mg L-1 fulvic acid concentration.