RESUMO Objetivo: Avaliar a alteração dimensional de modelos edêntulos fabricados em silicone laboratorial de alta densidade em diferentes tempos de armazenagem. Métodos: Um modelo mestre metálico simulando uma maxila edêntula foi utilizado. O modelo possuía projeções oclusais de 1,8 cm localizadas nas regiões de caninos (A e B) e molares (C e D), permitindo a mensuração das distâncias lineares AB, BC, CD, DA, AC e BD. Um molde foi fabricado em silicone laboratorial para duplicação do modelo mestre com os seguintes materiais (n = 10): G1: Zetalabor 85, G2: Titanium 95, G3: Platinum 95 e G4: Gesso tipo III (controle). As amostras foram fotografadas e mensuradas com auxílio de um software (Image J) nos tempos T1 (baseline) e T2 (após uma semana de confecção). Os dados obtidos foram avaliados estatisticamente utilizando os testes não paramétricos de Kruskal- Wallis e Dunn (α = 0.05). Resultados: O tempo de armazenagem influenciou o comportamento dos materiais avaliados. Todos os grupos apresentaram alterações dimensionais em ambos os temos de avaliação e o G2 apresentou os melhores resultados. Apenas o grupo G1 mostrou alteração dimensional dependente da região mensurada. Conclusão: Silicones laboratoriais de alta densidade mostraram resultados satisfatórias de alteração dimensional quando comparados ao gesso tipo III. O material Titanium 95foi o mais estável e pode ser recomendado como alternativa para a confecção de modelos edêntulos. Objetivo Métodos utilizado 18 1 8 1, A B C D, D , D) AB BC CD DA BD n 10 10) G 85 G3 9 G4 controle. controle . (controle) Image J T baseline (baseline após confecção. confecção) Kruskal α 0.05. 005 0.05 0 05 0.05) Resultados mensurada Conclusão (controle 00 0.0 0.

ABSTRACT Objective: To evaluate the dimensional change of edentulous models made of high density laboratory silicones at different storagetimes. Methods: A metallic master model simulating an edentulous maxilla was used. The model had projections of 1.8 cm located in the regions of canines (A and B) and molars (C and D) allowing the linear measurement of distances AB, BC, CD, DA, AC and BD. A laboratory silicone mold was made for duplication of master model in the following materials (n = 10): G1: Zetalabor 85, G2: Titanium 95, G3: Platinum 95 and G4: Gypsum type III (control). The samples were photographed and measured using a software (Image J) at times T1 (baseline) and T2 (after one week of models fabrication). The data were statistically analyzed using Kruskal- Wallis and Dun non-parametric tests (α = 0.05). Results: The storage time influenced the behavior of the materials evaluated. All groups presented dimensional changes in both times and the group Tit95 presented the best results. Only Zet85 group showed a different behavior related to the region of the model. Conclusions: The high density laboratory silicones showed satisfactory results when compared to the gypsum group. Tit95 was the most stable material and it can be recommended as an edentulous model for total protheses. Objective storagetimes Methods used 18 1 8 1. B C D AB BC CD DA BD n 10 10) G1 G 85 G2 G3 9 G4 control. control . (control) Image J T baseline (baseline after fabrication. fabrication fabrication) Kruskal nonparametric non parametric α 0.05. 005 0.05 0 05 0.05) Results evaluated Tit Tit9 Zet Zet8 Conclusions protheses (control 00 0.0 0.

ABSTRACT: This study aimed to compare the trueness and precision of physical models manufactured chairside (intraoral scanner and 3D printed) or by plaster models obtained using impression with alginate or addition silicone. A full- arch stainless steel die was impressed to obtain ten physical models for each group. The models were measured in a stereomicroscope, considering four linear distances. To assess the precision accuracy, an analysis of the measurement variability was carried out, identified by the coefficients of variation and by the Levene’s test to compare the groups. To analyze trueness, the data average was subtracted from the database and compared considering alpha as 5 %. Considering precision, the higher dispersion of data occurred in the models obtained with silicone impression. And for trueness, Kruskal Wallis and Dunn tests results did not indicate differences between the groups in the anteroposterior linear distances (p> 0.05). Only in anterior transverse distance obtained through TRIOS (0.31 mm), it presented lower accuracy compared to the models from silicone impression (0.13 mm); however, at transverse posterior distance, the models from silicone impression showed the lowest accuracy (p <0.05). There was no difference between the models from scanning (p> 0.05). The physical dental models obtained by digital and analog workflows showed acceptable dimensional accuracy expressed by high precision and trueness. There is no difference between the evaluated intraoral scanner systems and the impression materials for the full-arch impression.

RESUMEN: Este estudio tuvo como objetivo comparar la veracidad y precisión de modelos físicos fabricados en la clínica dental (escáner intraoral e impreso en 3D) o por modelos de yeso obtenidos mediante impresión con alginato o silicona de adición. Una matriz de acero inoxidable de arco completo fue impresa para obtener diez modelos físicos para cada grupo. Los modelos se midieron en un estereomicroscopio, considerando cuatro distancias lineales. Se realizó un análisis de la variabilidad de la medida para evaluar la precisión, identificada por los coeficientes de variación y por la prueba de Levene para comparar los grupos. Para analizar la veracidad, el promedio de los datos se restó de la base de datos y se comparó considerando alfa como 5 %. Considerando la precisión, la mayor dispersión de datos ocurrió en los modelos obtenidos con impresión de silicona. Y para la veracidad, los resultados de las pruebas de Kruskal Wallis y Dunn no indicaron diferencias entre los grupos en las distancias lineales anteroposteriores (p> 0,05). Solo en la distancia transversal anterior obtenida mediante TRIOS (0,31 mm) presentó menor precisión en comparación con los modelos de impresión de silicona (0,13 mm); sin embargo, la distancia transversal posterior, los modelos de impresión de silicona mostraron la menor precisión (p <0,05). No hubo diferencia entre los modelos de escaneo (p> 0,05). Los modelos dentales físicos obtenidos mediante flujos de trabajo digitales y analógicos mostraron una precisión dimensional aceptable expresada por alta precisión y veracidad. No se observó diferencia entre los sistemas de escáner intraoral evaluados y los materiales de impresión para la impresión de arco completa.

ABSTRACT The aim of this study was to verify the effectiveness of alternative techniques for measuring the linear dimensional change of molds obtained by different impression materials. A stainless-steel die containing three lines was used to get the impressions. The impression materials were handled according to the manufacturers' instructions. After gelation/polymerization time, the molds (n=12) were stored for 30 minutes and the lines were subsequently measured using: a microscope (Olympus Measuring Microscope STM; Olympus Optical Co) with a 30x magnification (MM, control group), a digital caliper (Mitutoyo Digimatic; Kawasaki) (DC) and digitization using a digital camera (Canon EOS Rebel 3Ti; Canon) (DI). For each mold, a mean of the length of the lines was obtained. For each impression material, the difference in the length between the metallic matrix and the mold was considered as linear dimensional change (%). The data were submitted to the non-parametric Kolmogorov-Smirnov test, followed by one-way Analysis of Variance (ANOVA) for each material, and the means were compared by the Tukey test (α=0.05). The DI group promoted values of dimensional accuracy without significant differences with the control group (MM), except for the putty-body condensation silicone. The DC group showed significant differences for MM and DI groups for all impression materials tested. The DI group showed to be a reliable methodology (Standard error of the mean <10%) to measure the linear dimensional change of all impression materials. The DI group presented molds with linear dimensional change values without significant differences with MM group, except for the putty-body addition silicone. The digitization is a reliable methodology to evaluate the linear dimensional changes of molds made with impression materials, except for the putty-body elastomeric impression materials.

Resumo Introdução Adultos com sequelas de doenças periodontais tendem a apresentar perda óssea, com consequente vestibularização dos incisivos superiores. Objetivo A influência da perda óssea e da inclinação do incisivo superior na distribuição de tensões devido a forças mastigatórias simuladas foram avaliadas nesse estudo. Material e método Modelos em resina epóxi foram confeccionados em três condições (sem perda óssea e com perda óssea de 5mm e 8mm). Aumentos na inclinação vestibular do incisivo superior de 10° e 20° foram obtidos com um bloco metálico chanfrado. Cargas de 100N foram aplicadas cinco vezes em cada condição usando uma máquina de ensaio universal. Os modelos foram observados e filmados com um polariscópio circular. Ordens de franjas isocromáticas (tensões) nas faces vestibular, lingual e apical foram registradas. A concordância dos dados foi avaliada pelo teste kappa ponderado e os resultados foram 0,89 e 0,82 para intra e interexaminadores, respectivamente. Resultado Os resultados dos testes de Kruskal-Wallis e SNK indicaram maiores tensões (2,0) com aumento da inclinação vestibular na face vestibular; maiores tensões (2,67) com aumento da perda óssea; maior tensão com a associação de perda óssea e inclinação vestibular (3,6); e as maiores tensões tenderam a concentrar-se na face vestibular, exceto em casos de inclinação normal e sem perda óssea (0,45). Conclusão Concluiu-se que aumentos tanto da inclinação vestibular dos incisivos superiores quanto da perda óssea aumentam as tensões perirradiculares, e a combinação desses fatores aumenta ainda mais as tensões devido às forças mastigatórias, com a maior concentração na face vestibular.

Abstract Introduction Adults with sequelae of periodontal disease tend to have bone loss, with consequent flaring of the maxillary incisors. Objective The influence of bone loss and the inclination of the maxillary incisor in the distribution of stresses due to simulated bite forces was studied. Material and method Models in epoxy resin were made in three conditions (without bone loss and with bone loss of 5mm and 8mm). Increases in the labial inclination of the maxillary incisor of 10° and 20° were obtained with a beveled metallic block. Loads of 100N were applied five times in each condition using a universal test machine. The models were observed and filmed with a circular polariscope. Orders of isochromatic fringes (stresses) on the labial, lingual, and apex surfaces were recorded. The agreement of the data was evaluated using the weighted kappa test, and the results were 0.89 and 0.82 for intra- and inter-examiners, respectively. Result The results of the Kruskal–Wallis and SNK tests indicated higher stresses (2.0) with increased labial inclination in the labial surface; higher stresses (2.67) with increased bone loss; higher greater stresses with the association of bone loss and labial-inclination (3.6); and the highest stresses tended to concentrate on the labial surfaces, except in cases of normal inclination and without bone loss (0.45). Conclusion It was concluded that increases in both the labial inclination of the maxillary incisors and bone loss increase periradicular stresses, and the combination of these factors further increases the stresses due to bite forces, with the highest concentration on the labial side.

OBJETIVO: comparar as ancoragens dentária e esquelética na retração do canino inferior, por meio do estudo da distribuição de tensões. MÉTODOS: foi confeccionado um modelo fotoelástico de segundo molar a canino, sem o primeiro pré-molar, e simulada a retração do canino inferior com elástico preso a dois tipos de ancoragem: dentária, no primeiro molar conjugado aos dentes adjacentes; e ancoragem esquelética, em gancho simulando o mini-implante. As forças foram aplicadas 10 vezes e observadas no polariscópio circular. As tensões no canino inferior foram registradas em 7 regiões. O teste de Mann-Whitney foi aplicado para comparar as tensões em cada região, considerando os dois sistemas de ancoragem. As tensões nas regiões perirradiculares do canino foram comparadas pelo teste de Kruskal-Wallis. RESULTADOS: as tensões foram similares tanto na região cervical quanto no terço médio. No terço apical, as tensões associadas à ancoragem esquelética foram maiores que as tensões associadas à ancoragem dentária. Os resultados do teste de Kruskal-Wallis mostraram que as maiores tensões foram identificadas nas regiões cervicodistal, apicodistal e na região do ápice com o uso da ancoragem dentária; e com o uso da ancoragem esquelética, as maiores tensões se localizaram nas regiões apicodistal, apicomesial, cervicodistal e no ápice. CONCLUSÃO: o uso de ancoragem esquelética na retração promoveu maior tensão no terço apical do que o uso da ancoragem dentária, indicando um componente intrusivo devido à direção da força decorrente da posição do mini-implante e do gancho do braquete do canino.

OBJECTIVE: To compare dental and skeletal anchorages in mandibular canine retraction by means of a stress distribution analysis. METHODS: A photoelastic model was produced from second molar to canine, without the first premolar, and mandibular canine retraction was simulated by a rubber band tied to two types of anchorage: dental anchorage, in the first molar attached to adjacent teeth, and skeletal anchorage with a hook simulating the mini-implant. The forces were applied 10 times and observed in a circular polariscope. The stresses located in the mandibular canine were recorded in 7 regions. The Mann-Whitney test was employed to compare the stress in each region and between both anchorage systems. The stresses in the mandibular canine periradicular regions were compared by the Kruskal-Wallis test. RESULTS: Stresses were similar in the cervical region and the middle third. In the apical third, the stresses associated with skeletal anchorage were higher than the stresses associated with dental anchorage. The results of the Kruskal-Wallis test showed that the highest stresses were identified in the cervical-distal, apical-distal, and apex regions with the use of dental anchorage, and in the apical-distal, apical-mesial, cervical-distal, and apex regions with the use of skeletal anchorage. CONCLUSIONS: The use of skeletal anchorage in canine retraction caused greater stress in the apical third than the use of dental anchorage, which indicates an intrusive component resulting from the direction of the force due to the position of the mini-implant and the bracket hook of the canine.

The purpose of this study was to evaluate the dimensional accuracy of different materials used in the confection of dies. Two stainless steel standard models were confected. One of the models, which was 2 mm larger than the other model, was used to provide a uniform relief for the two-step putty-wash impression technique. Thirty impressions were obtained using a polyvinyl siloxane impression material and randomly divided into three groups (n = 10) according to the type of casting material: type IV dental stone, commercially available epoxy resin (Tri-Epoxy), and industrial epoxy resin (Sikadur). After the setting/polymerization of the casting material, the dimensional stability was measured in terms of the height, diameter of the base and diameter of the top from the obtained dies and from the standard metal model using a profile projector. Results were analyzed by ANOVA and Dunnet test (α = 0.05). In the height values, no significant difference was observed between the groups, except for Sikadur casts, which showed lower mean values. The Tri-Epoxi group showed statistically lower mean base diameter values, compared with the other groups, and both epoxy resin groups showed statistically lower mean top diameter values, compared with that for the type IV dental stone group. We concluded that type IV gypsum and the commercially available epoxy resin showed similar behavior in most areas. The industrial epoxy resin did not show the same characteristics, although the diameter of the base obtained with it was similar to that obtained with type IV dental stone.

The aim of this study was to evaluate the accuracy of three implant transfer impression techniques. Four groups (n = 5) were defined, according to the technique: TC - tapered copings without splint; SC - square copings without splint; SCS - square copings splinted with dental floss and acrylic resin, and CG (control group) - master model with four external hexagonal implants and a superstructure. Individual trays and polyether were used for the impression. All casts were checked for their fit into the master superstructure; for this, all four screws were placed in the implants. Digital photos were taken and images were analyzed using UTHSCSA ImageTool software. Statistical analyses were performed using one-way analysis of variance and Student’s t test (p < 0.05). The means and standard deviation were (µm): CG = 2.03 ± 0.00, TC = 14.74 ± 3.41, SC = 12.08 ± 2.56, and SCS = 6.51 ± 0.09. The control group was found to be statistically different from the TC and SC groups. Within the limitations of this study, all groups presented clinically acceptable standard gap values, and the SCS group showed no statistical difference in relation to the CG (control group), demonstrating more accuracy and fidelity to transfer implants.

During clinical practice, when performing prosthetic rehabilitation with single crowns, improper reproduction of the dental contour by the dental laboratory is a common occurrence. Therefore, the present study evaluated the fidelity of the reproduction of the buccal contour in an upper left canine performed by three Dental Prosthesis Technicians (DPT) using the indirect laminate veneer technique. First, the DPTs confected the veneers based on a model obtained from the upper arch of a dental dummy, containing a replica of an upper left canine with a prosthetic preparation for a laminate veneer. Then, the same DPTs received other identical models, now with the replica of the upper left canine with no preparation, to be used as an anatomical reference for confecting the laminate veneers. The laminate veneers were then bonded to the plaster models and had their buccal contour individually measured. Measurements were also made of the buccal contour of the reference canine. The data were analyzed by ANOVA and the t-test (p = 0.05). Results showed 100% of buccal overcontour when the laminate veneers were compared to the reference canine, regardless of which DPT confected the veneer and regardless of using or not the anatomical reference. The DPTs who participated in the present study were unable to acomplish a faithful anatomical reproduction of the buccal contour, creating an overcontour in all samples. This situation may be responsible for increasing the probability of periodontal and esthetic harm in clinical practice.