INFLUENCE OF THE PROCEDURE FOR GRANULOMETRIC SAMPLE ADJUSTMENT OF RED CERAMIC AGGREGATED WITH DIMENSION STONE WASTES FOR CLASSIFICATION ACCORDING TO THE ABNT CRITERIA’S. In order to clarify questions about the granulometric preparation of samples for the classification of solid wastes according to the Brazilian technical standard (NBR 10004/04), solubilization tests were carried out on red ceramic specimens made with conventional clay aggregated with ornamental rock residues. Samples were prepared by fragmentation and milling to verify the effects on metals releasing to the extractor medium. The specimens were made with 80% clay, 20% residue and 10% (m/m) moisture and sintered at 1000 °C. The data show that ceramics made with conventional clay, when discarded, will produce non inert wastes, as well as the ceramics made with dimension stone wastes added to the conventional raw material, according to the granulometry of its particles. After all, the metals concentration in the solubilization test are influenced by the sample granulometry. This paper shows that the method of granulometric adjustment should be detailed in the technical standard for solubilization tests (NBR 10006/04), in order to ensure the reliability of the method for classification of solid wastes. CRITERIAS. CRITERIAS CRITERIA S. S CRITERIA’S NBR 10004/04, 1000404 10004/04 , 10004 04 10004/04) residues medium 80 20 10 m/m mm m (m/m 100 C °C discarded material particles all 10006/04, 1000604 10006/04 10006 10006/04) 100040 10004/0 0 8 2 1 100060 10006/0 10004/ 10006/

RESUMO Embora vários trabalhos proponham aplicações para os resíduos finos gerados no beneficiamento de rochas ornamentais, ainda não há evidências das vantagens financeiras para tal aproveitamento. Assim, a descrição dos depósitos existentes, muitos deles construídos sem triagem ou qualquer medida de proteção ambiental, torna-se imprescindível para seu melhor gerenciamento. Este trabalho estudou a caracterização física, química e mineralógica, além da resistência mecânica de um depósito de resíduos tradicionais e de seu substrato geológico. Cerca de 75% das partículas que compõem os resíduos são menores do que 0,0625 mm e o teor de umidade varia entre 26 e 60%. Os valores de pH variam entre 8,2 e 10,5. Os elementos químicos predominantes são Si, Al, Fe e, em menor proporção, Ca, Na e K. Esses elementos compõem quartzo, plagioclásio, microclina, calcita, muscovita, biotita e zircão. Ao comparar as características dos resíduos com as do substrato geológico, não foram encontrados indícios de migração das substâncias químicas analisadas. Os Stantard Penetration Tests mostram que as camadas não apresentam resistência suficiente para receber fundações rasas. É provável que as concentrações de Fe em alguns níveis contribuam com o aumento da resistência mecânica em áreas localizadas do depósito.

ABSTRACT Although several works propose applications for the fine wastes generated by the dimension stones processing, the financial advantages of recovering these materials are not yet evident. Then, the description of the deposits, much of them constructed without screening or any environmental protection measure, becomes indispensable for their best management. This work studies the physical, chemical and mineralogical characterization, as well as the mechanical resistance of a traditional waste deposit and its geological substrate. Around 76% of the particles that compound the wastes are smaller than 0,0625 mm and their humidity vary between 26 and 60%. The pH-values are between 8.2 and 10.5. The major chemical elements are Si, Al, Fe, and, at less proportions, Ca, Na, and K. These elements compound quartz, plagioclase, microcline, calcite, muscovite, biotite, and zircon. When comparing the characteristics of the wastes with the geological substrate, indicatives of the analyzed substances’ migration was not found. The Standard Penetration Tests (SPT) show that the layer´s strength is not good enough to receive shallow foundations. It is probable that Fe concentrations at some levels contribute for incrementing the deposit´s mechanical resistance.

The study of die geometry is vital in determining the surface and mechanical properties of drawn wires, and consequently, their application. In this work, annealed electrolytic copper wire (ETP), with 0.5 mm original diameter was reduced by 19% in dies with 2β = 10º and 18º and Hc = 35 and 50%. The best experimental results were then studied by the Finite Element Method to simulate residual stress distribution. The experimental results show that the friction coefficient decreases as the wire drawing speed increases, and that low 2β and Hc values bring about the most favorable wiredrawing conditions. The simulation shows a variation in the axial and radial tensions, both for the compression and traction stresses on all regions during the wire drawing process. In conclusion, the influence of the internal die geometry on the drawn wire is clarified.