Abstract Besides the effects on the health of individuals, cigarette smoking can also interfere with the appearance of their teeth. Objective: To evaluate the effect of cigarette smoking-toothbrushing-cycling (CSTC) with whitening toothpastes on the roughness and optical behavior of bovine enamel for eight weeks. Material and Methods: Thirty bovine dentin/enamel discs, 8.0 mm in diameter and 2.0 mm thick, were randomly divided into three groups according to the toothpastes: whitening (Colgate Luminous White - CW and Oral B 3D White - OW), and a non-whitening (Colgate - C). The roughness, color (CIE L*a*b* system), translucency and gloss were measured before and after the specimens were submitted to CSTC. The topography of the specimens was analyzed by scanning electron microscopy. During the first week, the specimens were daily subjected to the consumption of 20 cigarettes and brushed (40 strokes/100 g) with the toothpastes' slurries. Thereafter, the CSTC was weekly applied in an accumulated model (140 cigarettes/280 strokes) for seven weeks. The data were submitted to two-way ANOVA, Tukey's HSD test, and paired-t test (α=0.05). Results: The three toothpastes produced significant changes in roughness, color, translucency and gloss (p<0.05). After eight weeks, the roughness and the gloss produced by the three toothpastes were similar (p>0.05), while OW produced the lowest color change and the translucency of C was lower than that of CW (p<0.05). The three toothpastes produced a significant decrease in L* values and a significant increase in a* values after eight weeks (p<0.05). No significant difference in the b* coordinate was found for OW (p=0.13) There were topographic changes in the enamel surfaces. Conclusions: The whitening toothpastes increased the roughness, changed the topography and were not able to maintain the optical stability of enamel exposed over eight weeks.

Marginal integrity is one of the most crucial aspects involved in the clinical longevity of resin composite restorations. Objective To analyze the marginal integrity of restorations produced with a model composite based on polyhedral oligomeric silsesquioxane (POSS). Material and Methods A base composite (B) was produced with an organic matrix with UDMA/TEGDMA and 70 wt.% of barium borosilicate glass particles. To produce the model composite, 25 wt.% of UDMA were replaced by POSS (P25). The composites P90 and TPH3 (TP3) were used as positive and negative controls, respectively. Marginal integrity (%MI) was analyzed in bonded class I cavities. The volumetric polymerization shrinkage (%VS) and the polymerization shrinkage stress (Pss - MPa) were also evaluated. Results The values for %MI were as follows: P90 (100%) = TP3 (98.3%) = B (96.9%) > P25 (93.2%), (p<0.05). The %VS ranged from 1.4% (P90) to 4.9% (P25), while Pss ranged from 2.3 MPa (P90) to 3.9 MPa (B). For both properties, the composite P25 presented the worst results (4.9% and 3.6 MPa). Linear regression analysis showed a strong positive correlation between %VS and Pss (r=0.97), whereas the correlation between Pss and %MI was found to be moderate (r=0.76). Conclusions The addition of 25 wt.% of POSS in methacrylate organic matrix did not improve the marginal integrity of class I restorations. Filtek P90 showed lower polymerization shrinkage and shrinkage stress when compared to the experimental and commercial methacrylate composite.

O objetivo deste estudo foi analisar a absorção e a solubilidade de uma resina composta nanopartículada (Filtek Z350) e de uma híbrida (Filtek P60) em substâncias simuladoras do ambiente oral em um modelo de cavidade profunda. Uma cavidade cilíndrica, construída em uma raiz de um incisivo bovino, foi preenchida incrementalmente com as resinas compostas. Os cilindros obtidos foram seccionados perpendicularmente ao eixo para obtenção de discos com 1 mm de espessura, que foram divididos em 15 grupos (n=5) de acordo com a profundidade (1, 2, 3, 4 e 5 mm) e o meio de imersão (água destilada - AD, saliva artificial - SA e ácido lático - AL). A absorção e a solubilidade foram calculadas com base na norma ISO 4049:2000(E). Adicionalmente, o grau de conversão (GC%) foi calculado através de espectroscopia FT-IR. Os dados obtidos foram analisados usando análise de variância multifatorial, teste de Tukey HSD e análise de regressão linear (a=0,05). A resina composta híbrida apresentou o maior grau de conversão, sendo este influenciado pela profundidade da cavidade (p<0,05). A resina composta nanopartículada apresentou maiores valores de absorção e solubilidade (p<0,05). O meio de imersão influenciou a absorção e a solubilidade: AL>SA>AD (p<0,05). Ambos os fenômenos foram influenciados pela profundidade da cavidade, com os valores aumentando de 1 para 5 mm (p<0,05). A degradação de restaurações de resinas compostas pode ser maior em regiões profundas de restaurações classe II e quando o material é exposto à ácidos orgânicos produzidos pelo biofilme oral (ácido lático).

The aim of this study was to analyze the sorption and solubility of a nanofilled (Filtek Z350) and a midifilled (Filtek P60) resin composite in oral environment-like substances, in a simulated deep cavity. A cylindrical cavity prepared in a bovine incisor root was incrementally filled with resin composites. The obtained resin composite cylinders were cut perpendicularly to the axis to obtain 1-mm-thick discs that were divided into fifteen groups (n=5) according to depth (1, 2, 3, 4 and 5 mm) and immersion media (distilled water - DW, artificial saliva - AS and lactic acid - LA). The sorption and solubility were calculated based on ISO 4049:2000. Additionally, the degree of conversion (DC%) was calculated by FT-IR spectroscopy. Data were analyzed using multifactor analysis of variance (MANOVA) followed by Tukey's HSD post-hoc test and linear regression analysis (a=0.05). The DC% was higher for the midifilled resin composite and was negatively influenced by cavity depth (p<0.05). The nanofilled resin composite presented higher sorption and solubility than did the midifilled (p<0.05). The immersion media influenced the sorption and the solubility as follows: LA>AS>DW, (p<0.05). Both phenomena were influenced by cavity depth, with the sorption and solubility increasing from 1 to 5 mm (p<0.05). The degradation of resin composite restorations may be greater in the deepest regions of class II restorations when the composite is exposed to organic acids present in the oral biofilm (lactic acid).

Indirect restorations in contact with free gingival margins or principally within the gingival sulcus, where the presence of organic acids produced by oral biofilm is higher, may present faster degradation of the resin-based cement pellicle. Objectives To investigate the degradation of four resin-based cements: Rely X ARC (R), Variolink II (V), Enforce (E) and All Cem (A), after immersion in distilled water (DW), lactic acid (LA) and artificial saliva (AS) and to analyze the influence of the activation mode on this response. Material and Methods Two activation modes were evaluated: chemical (Ch) and dual (D). In the dual activation, a two-millimeter thick ceramic disk (IPS Empress System) was interposed between the specimen and light-curing unit tip. Specimens were desiccated, immersed in distilled water, artificial saliva and lactic acid 0.1 M at 37°C for 180 days, weighed daily for the first 7 days, and after 14, 21, 28, 90 and 180 days and were desiccated again. Sorption and solubility (µg/mm 3 ) were calculated based on ISO 4049. The data were submitted to multifactor analysis of variance (MANOVA) and Tukey's HSD test for media comparisons (α=0.05). Results Sorption was higher after immersion in LA (p<0.05) and increased significantly with time (p<0.05). Sorption was influenced by the activation mode: Ch>D (p<0.05). The lowest solubility was presented by R (p<0.05). Conclusions Lactic acid increased the degradation of resin-based cements. Moreover, the physical component of activation, i.e., light-activation, contributed to a low degradation of resin-based cements.

OBJECTIVE: This study analyzed the degree of conversion (DC%) of four resin-based cements (All Ceram, Enforce, Rely X ARC and Variolink II) activated by two modes (chemical and dual), and evaluated the decrease of DC% in the dual mode promoted by the interposition of a 2.0-mm-thick IPS Empress 2 disc. MATERIAL AND METHODS: In the chemical activation, the resin-based cements were prepared by mixing equal amounts of base and catalyst pastes. In the dual activation, after mixing, the cements were light-activated at 650 mW/cm² for 40 s. In a third group, the cements were light-activated through a 2.0-mm-thick IPS Empress 2 disc. The DC% was evaluated in a FT-IR spectrometer equipped with an attenuated total reflectance crystal (ATR). The data were analyzed by two-way ANOVA and Tukey's HSD test. RESULTS: For all resin-based cements, the DC% was significantly higher with dual activation, followed by dual activation through IPS Empress 2, and chemical activation (p<0.05). Irrespective of the activation mode, Rely X presented the highest DC% (p<0.05). Chemically activated Variolink and All Ceram showed the worst results (p<0.05). The DC% decreased significantly when activation was performed through a 2.0-mm-thick IPS Empress 2 disc (p<0.05). CONCLUSION: The results of the present study suggest that resin-based cements could present low DC% when the materials are dually activated through 2.0 mm of reinforced ceramic materials with translucency equal to or less than that of IPS-Empress 2.

OBJECTIVES: The purpose of this study was to evaluate the Vickers hardness number (VHN) and the in vitro marginal adaptation of inlay restorations of three hybrid composite resins (Filtek Z250, Opallis and Esthet-X) subjected to two post-cure treatments. MATERIAL AND METHODS: For the microhardness test, three different groups were prepared in accordance with the post-cure treatments: control group (only light cure for 40 s), autoclave group (light cure for 40 s + autoclave for 15 min at 130ºC); and microwave group (light cure for 40 s + microwave for 3 min at 450 W). To assess the marginal adaptation, the composite resin was inserted incrementally into a mesial-occlusal-distal cavity brass mold and each increment light-cured for 40 s. A previous reading in micrometers was taken at the cervical wall, using a stereomicroscope magnifying glass equipped with a digital video camera and image-analysis software. Subsequently, the specimens were subjected to the post-cure treatments (autoclave and microwave) and a reading was taken again at the cervical wall. Data were compared using ANOVA for the hardness test, split-plot ANOVA for the adaptation assessment and Tukey's test for multiple comparisons. A significance level of 5% was adopted for all analyses. RESULTS: The post-cure treatments increased the hardness of conventional composites (p<0.001) and the gap values of inlay restorations (p<0.01). Filtek Z250 showed higher hardness (p<0.001) and lower gap values than Opallis and Esthet-X (p<0.05). Gap values did not exceed 90 µm for any of the experimental conditions. CONCLUSION: The post-cure treatments increased the VHN and the gap values on the cervical floor of composite resin inlays. Moreover, Filtek Z250 showed the best results, with higher hardness and lower gap values.

This study analyzed the relationship between the degree of conversion (DC), solubility, and salivary sorption of a hybrid (Filtek P 60) and a nanofilled resin composite (Filtek Supreme), and evaluated the influence of the light-activation mode on these properties. Two light-activation modes were used: Conventional (C; 850 mW/cm² for 20 s) and Soft-start (SS; 100-1,000 mW/cm² for 10 s + 1,000 mW/cm² for 10 s). The DC (%) was evaluated by FT-Raman spectroscopy. The solubility and salivary sorption were measured after immersion in artificial saliva for 7 days. Data were analyzed by ANOVA and Student-Newman-Keuls' test and linear regression analysis (a = 0.05). The DC varied from 50.52% (nanofilled composite) to 57.15% (hybrid composite), and was influenced by the light-activation mode: C > SS. The solubility (0.45 mg/mm³) and salivary sorption (8.04 mg/mm³) of the nanofilled composite were greater than those of the hybrid composite (0.40 mg/mm³ / 6.87 mg/mm³), and were influenced by the light-activation mode: SS > C. Correlation was found between DC and solubility (r = - 0.89, p<0.05), as well as between solubility and salivary sorption (r = 0.95). These findings suggest that nanofilled composites may present higher degradation in the oral environment than hybrid ones. Soft-start light-activation mode may increase the solubility of resin composites.

OBJETVO: Este estudo avaliou a profundidade de polimerização de cinco compósitos fotopolimerizáveis submetidos a diferentes métodos de fotoativação. MATERIAL E MÉTODO: Cavidades em forma de canaleta com 5 mm de comprimento, preparadas nas faces vestibulares de terceiros molares, foram restauradas com os compósitos P-60, A-110, Admira, Z-250 e Supreme. Os materiais foram fotoativados pelo topo das cavidades com três técnicas (Grupo 1 - Convencional (C): 500 mW / cm² / 40 s; Grupo 2 - Soft-Start (SS): 250 mW / cm² / 20 s + 500 mW / cm² / 20 s + 500 mW / cm² / 10 s e Grupo 3 - LED: 250 mW / cm² / 40 s). Após a fotoativação, as superfícies longitudinais dos materiais foram polidas e marcadas com uma escala milimetrada com 4 mm de comprimento. A profundidade de polimerização foi avaliada através do número de dureza Knoop (NDK), com cinco indentações a cada milímetro. Os dados originais foram submetidos à Análise de Variância de três fatores e teste de Fisher para comparações entre médias (alfa = 0,01). RESULTADOS: Todos os materiais apresentaram diminuição do NDK do primeiro para o terceiro milímetro (p < 0,01). Os resultados obtidos com os Grupos Convencional e Soft-Start foram similares e superiores ao Grupo LED (p < 0,01). CONCLUSÃO: Este desempenho pode ser relacionado às diferenças nas densidades de energia obtidas com os métodos de fotoativação utilizados.

OBJECTIVE: This study evaluated the depth of cure of five dental composites submitted to different light-curing modes. MATERIAL AND METHODS: Canal-shaped cavities with 5mm of length were prepared on the buccal surfaces of extracted third molars, and restored using P-60, A-110, Admira, Z-250 and Supreme resin composites. Materials were light-cured from the top, according to three modes (Group 1- Conventional (C): 500 mW/cm² / 40 s; Group 2 - Soft-Start (SS): 250 mW/cm²/ 20 s + 500 mW/cm²/ 20 s + 500 mW/cm²/ 10 s and Group 3 - LED: 250 mW/cm²/ 40 s). After that, cavity longitudinal surfaces were polished and marked with a millimeter scale of 4mm of length. Depth of cure was evaluated by means of Knoop hardness number (KHN), so that five indentations were performed at each millimeter. Original data were submitted to three-way ANOVA and Fisher's LSD test (alpha = 0.01). RESULTS: All materials presented a significant reduction on KHN from first to third millimeter. Regarding depth of cure, the results obtained for Conventional and Soft-Start modes were similar, but statistically superiors to those found for group 3 (LED). CONCLUSION: This performance may be related to the differences among energy densities obtained with different light-curing modes.