In this study, the effects of incorporating recycled photopolymer-plate residues from a packaging flexography process into polyester-glass fiber composites were examined. Ternary composites with an unsaturated polyester matrix with elastomer particles from recycled photopolymer-plate residues were evaluated using two types of glass fibers: in the forms of a fabric with bidirectional fibers and a blanket with multidirectional fibers. The composites were prepared by hand lay-up lamination using different rubber contents (0, 2.5, 5, and 10 wt% based on the polyester resin mass fraction), and were characterized for their void content, flexural and impact strengths, and dynamic mechanical properties. Primary results indicated that the incorporation of the rubber particles increased the difficulty of lamination, while promoting greater void formation with higher filler content. The rubber particles decreased the impact resistance properties but did not reduce the flexural strength or storage modulus, indicating that despite the elastomeric composition, this residue from the photopolymer plates showed a reinforcing rather than toughening character. study photopolymerplate plate polyesterglass examined layup lay up 0, 0 (0 25 2 5 2.5 1 wt fraction, fraction , fraction) content strengths modulus composition character ( 2.

Abstract Biodegradability of five commercial plastic bags labelled as “biodegradable” and two referent materials were studied by a soil test for three months. As a control experiment, for studying abiotic degradation under the climatic impact (ultraviolet, temperature, and moisture) a test in a weatherometer was performed. The changes in bag samples after tests were detected by optical microscopy, Fourier-transform infrared spectroscopy, differential scanning calorimetry, and tensile testing. It was found that all the bags may be separated into two groups: based on polyesters and based on polyolefins with oxo-additives. The second group demonstrated an ability to oxidation under UV radiation. The content of chalk filler provided a mass loss of the samples under soil and climatic tests due to its washing out. Three samples on the polyester basis filled with starch (the first group) had different compositions (polymers in the matrix were different). They showed a high biodegradability under soil conditions: mass loss was 14-21%, tensile strength decreased by more than 43%, and the surface was covered by the mycelium net. However, according to FTIR-spectroscopy, at the initial stage only starch filler biodegraded intensively, while polymer matrix was stable. biodegradable “biodegradable months experiment ultraviolet, ultraviolet (ultraviolet temperature moisture performed microscopy Fouriertransform Fourier transform spectroscopy calorimetry testing groups oxoadditives. oxoadditives oxo additives. additives oxo-additives radiation out polymers different. . different) conditions 1421%, 1421 14 21%, 21 14-21% 43 43% net However FTIRspectroscopy, FTIRspectroscopy FTIR FTIR-spectroscopy intensively stable 1421% 142 1 21% 2 14-21 4 14-2 14-

Abstract Continuous development, improvement and innovation of ballistic material systems with superior energy absorption performance has been the subject of numerous works nowadays. Some research has been carried out with the objective of replacing traditional metallic and ceramic materials and composites with high-performance polymeric composites. Due to their excellent properties, multi-scale polymer composites have been used in the most varied segments of the industry, being recently researched in applications such as ballistic materials. This work promotes the combination of high-strength three-dimensional woven aramid fiber fabrics with vinyl ester resin to produce a panel through the compression molding process. The resin was reinforced with graphene nanoplatelets (0.1, 0.2 and 0.3% wt). The impact, tensile and flexural strength were evaluated, along with dynamic-mechanical analysis by DMA and by Hopkinson split bar test, indicating a trend of better performance for the composite containing 0.1% of graphene nanoplatelets.

RESUMEN La cinética del secado de hojas de yerba mate del sur de Brasil se investigó experimental y teóricamente en un horno de secado a 70°C. Se evaluó el efecto de las condiciones de secado sobre la proporción de humedad, la velocidad de secado y la difusividad efectiva de las hojas de yerba mate. Se ajustaron cinco modelos de secado a los datos experimentales. Además, se determinó la concentración de As, Cd, Pb, Ni, Cr y Hg en las hojas de yerba mate mediante espectrometría de emisión óptica de plasma de acoplamiento inductivo (ICP-OES). Los resultados revelaron que todas las muestras solo presentaron un período de tiempo de velocidad decreciente sin periodo de velocidad constante de secado. El modelo Midilli mostró el mejor ajuste de los datos experimentales. Todas las muestras presentaron niveles de Hg superiores a los permitidos por la legislación brasileña. Se requieren programas de monitoreo y otros estudios para prevenir la ingesta de productos de yerba mate contaminados con metales tóxicos.

ABSTRACT The drying kinetics of yerba mate leaves from southern Brazil was investigated theoretically and experimentally in a drying oven at 70°C. The effect of drying conditions on the moisture ratio, drying rate, and effective diffusivity of yerba mate leaves was evaluated. Five drying models were fitted to experimental data. Additionally, the concentrations of As, Cd, Pb, Ni, Cr, and Hg in the yerba mate leaves were determined using inductively coupled plasma optic emission spectrometry (ICP-OES). The results revealed that all samples only showed a falling rate period without a constant rate of drying. The Midilli model showed the best fit of experimental data. All samples showed levels of Hg higher than those permitted by Brazilian legislation. Monitoring programs and other studies are required to prevent the intake of yerba mate products contaminated with toxic metals.

Abstract: Thermal analysis is a powerful tool to predict the composition and thermal stability of different materials. In this work, thermogravimetric analysis of Cedrela odorata, Marmaroxylon racemosum and Tectona grandis was carried out at four different heating rates (5°C·min-1, 10°C·min-1, 20°C·min-1 and 40°C·min-1) in a non-isothermal condition. The degradation kinetics was evaluated based on Flynn-Wall-Ozawa and Criado methods. The half-life time of wood degradation reaction was also studied. The wood thermal degradation process in an oxidizing atmosphere can be divided in dehydration, devolatilization, and combustion. The kinetic results revels apparent activation energy values of 130-240 kJ·mol-1 for Tectona grandis, 150-191 kJ·mol-1 for Marmaroxylon racemosum and 188-205 kJ·mol-1 for Cedrela odorata, when conversion values ranged from 0,1-0,5. The most probable degradation mechanism for wood species studied is a diffusion model based on a three-dimensional diffusion. Cedrela odorata presented the lowest reaction half-life time while Marmaroxylon racemosum showed the highest. On the basis of these results, it can be concluded that Flynn-Wall-Ozawa and Criado methods associated with half-life time of reaction may contribute to better understand the wood degradation before use it in polymer composites.

Abstract: In this work, thermal expansion and morphological properties of recycled polypropylene wood flour composites were evaluated in order to verify the effect caused by the usage of a natural oil as coupling agent. The natural oil used as coupling agent was octanoic acid (C8), maleic anhydride grafted polypropylene (MAPP), widely used in industry but from non-renewable source, was also used for comparison. Composites were obtained by twin screw extrusion and injection molded. The results showed that the addition of octanoic acid and maleic anhydride grafted polypropylene reduced the coefficient of thermal expansion of the composites. The dependence of melt viscosity obeyed the Arrhenius-Eyring expression, and the activation energy values for composite viscous flow were higher than matrix. The composite morphology revels that octanoic acid promotes strong interfacial adhesion between filler and matrix, similar to that observed when maleic anhydride grafted polypropylene were used. Octanoic acid showed similar results when compared with maleic anhydride grafted polypropylene in all properties evaluated, indicating that can be used as an alternative instead of use coupling agent from non-renewable sources.

In this study, poly(acrylonitrile-co-butadiene-co-styrene)/hollow glass microspheres (ABS/HGM) composites were prepared by means of a twin-screw extruder. HGM were incorporated at different loadings of 2.5, 5.0, and 7.5 wt.% at the central extruder zone with different types of ABS. The morphological, physical, thermal, rheological and mechanical properties of ABS/HGM composites were investigated. Statistical analysis reveals that high impact ABS addition is significant for improving composites’ impact strength. The results also indicated that addition of 5.0 wt.% of HGM along with 5.0 wt.% of powdery ABS at the central extruder zone maintains the HGM integrity while powdery ABS contributes to better filler dispersion in the matrix resulting in light-weight composites having improved mechanical properties.

Abstract: In this work, the potential for usage recycled polystyrene and wood flour wastes as materials for development wood plastic composites was evaluated. The effects of wood flour loading and coupling agent addition on the mechanical, dynamic mechanical and morphological properties of polystyrene wood flour composites were examined. The results showed that the mechanical properties decreased with the wood flour loading. However, an improvement in composite compatibility was observed when the coupling agent was used resulting in the increase of mechanical and dynamic mechanical properties. A morphological study demonstrates the positive effect in the interfacial adhesion between filler and matrix caused by the coupling agent addition. Based on the findings of this work, both waste materials can be used for development composites with higher performance.

In this work, post-consumer polypropylene and wood flour from Pinus elliottii were used to produce wood plastic composites. The effect of polypropylene grafted with itaconic acid used as a coupling agent on mechanical properties, thermal stability and morphology of the composites was investigated and compared with the composite developed with polypropylene grafted with maleic anhydride, commonly used as coupling agent in wood plastic composites. Composites with 30 wt% of wood flour and 2 wt% of coupling agent were produced in a co-rotating twin-screw extruder and after were injection molded. The mechanical properties showed that flexural strength improved on 29% and 35% with addition of polypropylene grafted with itaconic acid and polypropylene grafted with maleic anhydride respectively, when compared with the wood plastic composites without coupling agent. On the other hand, the incorporation of polypropylene grafted with itaconic acid does not change the impact strength values significantly. Additionally, the temperature corresponding to 3 wt% of weight loss determined by thermogravimetry for composites with polypropylene grafted with itaconic acid increased by 14°C when compared with wood plastic composites without coupling agent, while addition of polypropylene grafted with maleic anhydride increased approximately 6°C the composite thermal stability. A morphological study revealed the positive effect of the polypropylene grafted with itaconic acid on the interfacial bonding of recycled polypropylene and wood flour.

In this work Eucalyptus grandis and Dipteryx odorata were submitted to photodegradation by ultraviolet radiation. The effect of ultraviolet radiation irradiation on the color change and chemical composition of each wood flour were evaluated. The samples were submitted to a total of 500h of artificial weathering using condensation stages and ultraviolet radiation B irradiation cycles. The changes in wood flour color were monitored by spectrocolorimetry, while the changes in wood chemical composition were evaluated by Fourier transform infrared spectroscopy. Both species showed changes in color with increased exposure time to artificial weathering. For both wood species the variation in color change was considered very appreciable after 500h. The Eucalyptus grandis specie showed appreciable color change after 120h, while for Dipteryx odorata specie the color change is appreciable only after 240h. The Fourier transform infrared spectroscopy results showed that lignin was strongly degrades by ultraviolet radiation radiation in both species. However, Dipteryx odorata was more resistant to photodegradation than Eucalyptus grandis, probably due to lower lignin content in this wood. The results clearly indicated that for the wood species studied the rate of weathering is influenced by wood species.

The thermal behavior of lignins from softwood and hardwood species has been investigated using thermogravimetry and differential scanning calorimetry. Klason Lignin from Pinus taeda and Klason lignin from Eucalyptus grandis were studied. The differential scanning calorimetry results showed that both Klason lignins studied presented similar glass transition temperature. Thermogravimetric results showed that the lignin degradation occurs in three stages. The Klason lignin of Pinus taeda is more thermally stable than Eucalyptus grandis, probably because of the higher thermal stability of the guaiacyl units in softwood lignin. The degradation of both lignins initiate by a diffusion process. However when the conversion values are higher than 0,1 the lignin degradation mechanism is a complex procedure and involves the degradation of a highly condensed aromatic structure formed at the previous degradation stages.

RESUMO O objetivo deste trabalho foi caracterizar quatro amostras de resíduos de madeira oriundas da indústria madeireira a fim de obter informações prévias sobre a estrutura e as propriedades da madeira antes do seu uso como biocombustível ou como reforço em compósitos. A influência dos componentes da madeira na estabilidade térmica de diferentes espécies de madeira foi investigada utilizando termogravimetria, calorimetria exploratória diferencial e microscopia eletrônica de varredura. Quatro espécies de madeira, Eucalyptus grandis (EUG), Pinus elliottii (PIE), Dipteryx odorata (DIP) e Mezilaurus itauba (ITA), foram utilizadas neste estudo. Os resultados mostraram que elevadas quantidades de extrativos podem formar uma fina película na superfície da fibra de madeira, o que pode acelerar o processo de degradação e reduzir a estabilidade térmica da madeira.

ABSTRACT The aim of this work was characterize four wood waste samples from lumber industry in order to obtain previous information about structure and properties of wood before use it as a biofuel or as reinforcement in composite formulations. The influence of wood components on the thermal degradation stability of different wood species has been investigated using thermogravimetry, differential scanning calorimetry and scanning electron microscopy. Four wood species, Eucalyptus grandis (EUG), Pinus elliottii (PIE), Dipteryx odorata (DIP) and Mezilaurus itauba (ITA), were used in this study. The results showed that higher extractives contents may form a thin film on the wood fiber surface which can accelerate the degradation process and reduce the wood thermal stability

ABSTRACT The usage of natural fibers on the composites development has grown rapidly in the recent years due to the fibers plentiful availability, renewable source, low density and biodegradability. However, there are some drawbacks, for instance, the fiber dispersion on a polyolefin matrix. In this work, the influence of processing speed on the mechanical and dynamic mechanical properties of polystyrene (PS) filled with cellulose fiber composites was investigated. The composites were processed on a twin-screw co-rotating extruder, using screw speeds of 200 rpm, 400 rpm and 600 rpm. The dynamic mechanical properties and the mechanical properties were investigated as a function of fiber content. The composites processed on a screw speed of 400 rpm had presented an increase on flexural and impact strength, compared to the composites processed at 200 rpm. The flexural and storage modulus had increased when increasing the fiber content, as well as increasing the processing speed. The greater fiber dispersion obtained at a screw speed of 400 rpm hinders the agglomeration arrangement and distributes the fibers more equally on the matrix. The increase on processing speed probably generates a fiber size reduction, increasing the fiber superficial area and generating a greater contact with the matrix as well. Therefore, the efforts transference of matrix to fibers is improved, originating an increase on the evaluated properties.

The influence of extractive content on the thermal stability and kinetic degradation of two wood species has been investigated using chemical analysis and thermogravimetry. Two wood species were studied: Pinus taeda and Eucalyptus grandis. Thermogravimetric results showed that higher extractive contents in the wood accelerate the degradation process and promote an increase in the conversion values at lower temperatures reducing the wood thermal stability. After removing the extractives from wood the thermal stability for both wood species increased. The results also demonstrated that prior information about the wood composition can be helpful to increase the range of industrial applications of wood.

In this work, the influence of three types of styrene maleic anhydride (SMA) oligomers on the adhesion of polystyrene wood plastic composites (WPC) was investigated. The composites were processed on a twin-screw co-rotating extruder below 200°C using 20 wt% of wood flour. The styrene maleic anhydride with different content of maleic anhydride groups, 30%, 25% and 20% (w/w) and levels of 1, 2 and 4% of coupling agents (styrene maleic anhydride 2000, styrene maleic anhydride 3000 and styrene maleic anhydride EF40) in the composite formulations were tested. Mechanical, physical and morphologic properties were evaluated. The styrene maleic anhydride improves the compatibility of hydrophilic wood flour with hydrophobic polystyrene matrix. It has been observed that the addition of styrene maleic anhydride increased the wood plastic composites mechanical properties with the incorporation of 2% wt of styrene maleic anhydride 2000. The mechanical properties showed to be dependent on content of maleic anhydride in the coupling agent. Treated and non-treated wood plastic composites showed similar density values, but the void content was reduced for treated composites. Scanning electron microscopy revel the better adhesion between polymer and matrix when coupling agent were used.