OBJECTIVES: To evaluate the effect of additives on the water sorption characteristics of Bis-GMA based copolymers and composites containing TEGDMA, CH3Bis-GMA or CF3Bis-GMA. MATERIAL AND METHODS: Fifteen experimental copolymers and corresponding composites were prepared combining Bis-GMA and TEGDMA, CH3Bis-GMA or CF3Bis-GMA, with aldehyde or diketone (24 and 32 mol%) totaling 30 groups. For composites, barium aluminosilicate glass and pyrogenic silica was added to comonomer mixtures. Photopolymerization was effected by 0.2 wt% each of camphorquinone and N,N-dimethyl-p-toluidine. Specimen densities in dry and water saturated conditions were obtained by Archimedes' method. Water sorption and desorption were evaluated in a desorption-sorption-desorption cycle. Water uptake (%WU), water desorption (%WD), equilibrium solubility (ES; µg/mm³), swelling (f) and volume increase (%V) were calculated using appropriate equations. RESULTS: All resins with additives had increased %WU and ES. TEGDMA-containing systems presented higher %WU, %WD, ES, f and %V values, followed by resins based on CH3Bis-GMA and CF3Bis-GMA. CONCLUSIONS: Aldehyde and diketone led to increases in the water sorption characteristics of experimental resins.

The effect of different propionaldehyde ratios on the properties of bis-GMA-based comonomers and copolymers diluted with propoxylated bis-GMA (CH3bis-GMA) was evaluated. Five experimental comonomers were prepared combining bis-GMA with CH3bis-GMA and propionaldehyde at 0, 2, 8, 16, 24 mol%. Light polymerization was effected with the use of 0.2 wt. (%) each of camphorquinone and N,N-dimethyl-p-toluidine. Resin degrees of conversion (%DC) were evaluated by FT-IR spectrophotometry and Tg by Differential Scanning Calorimeter. Complex viscosity (η*), the effect of temperature on η*, and Microhardness (H) for dry and wet samples were also determined. Data were analyzed by Student's t-test, one-way ANOVA and Tukey-Kramer test (α = 0.05). The group with 24 mol% additive had a significant increase in %DC and H, and the lowest comonomer Tg and η*. No remarkable variation was noted in copolymers Tg s. All resins presented Newtonian behavior of viscosity, which linearly decreased with increased temperature. The η* decreased sigmoidally as the additive ratio increased.

O objetivo desse estudo foi avaliar a alteração de rugosidade superficial de três cimentos resinosos após submetê-los a ciclos de escovação simulada e analisar qualitativamente a sua superfície através de observações microscópicas. Os materiais empregados neste estudo foram Enforce Sure Cure (Dentsply), Rely X (3M-ESPE) e Variolink II (Vivadent). Estes foram submetidos à ciclos de escovação simulada (100.000 ciclos para cada espécime) e a alteração de sua rugosidade superficial (antes e após escovação) foi avaliada. Para cada material e condição de rugosidade, espécimes foram selecionados, metalizados e observados em microscopia eletrônica de varredura (DSM 900 Zeiss). Baseado nas observações microscópicas e nos valores de alteração de rugosidade, todos os materiais apresentaram aumento de rugosidade aritmética (Ra) após ciclos de escovação simulada.

The objective of this work was to evaluate the surface roughness changes of three current resin cements after tooth brushing simulation, as well as discuss its relation with scanning electron microscopic observations. The materials employed were Enforce Sure Cure (Dentsply), Rely X (3M-ESPE) and Variolink II (Vivadent). They were subjected to brushing abrasion (100,000 strokes for each specimen) and the surface roughness alterations (before and after strokes) were detected. For each roughness test condition, specimens were coated with gold-palladium and observed on a DSM 900 Zeiss scanning electron microscope. Roughness changes values (Ra) were statistically increased after brushing strokes. Based on the microscopic observations and roughness changes analysis, all cements studied became rougher after brushing strokes.