Abstract Fixed orthodontic appliances may lead to biofilm accumulation around them that may increase caries risk. This study aimed to evaluate the influence of quaternary ammonium methacrylates (QAMs) on the physicochemical properties, cytotoxicity, and antibacterial activity of adhesive resins for orthodontic purposes. Methodology: A base resin was prepared with a comonomer blend and photoinitiator/co-initiator system. Two different QAMs were added to the base adhesive: dimethylaminododecyl methacrylate at 5 wt.% (DMADDM) or dimethylaminohexadecyl methacrylate (DMAHDM) at 10 wt.%. The base adhesive, without QAMs, (GC) and the commercial Transbond™ XT Primer 3M (GT) were used as control. The resins were tested immediately and after six months of aging in the water regarding the antibacterial activity and shear bond strength (SBS). The antibacterial activity was tested against Streptococcus mutans via metabolic activity assay (MTT test). The groups were also tested for the degree of conversion (DC) and cytotoxicity against keratinocytes. Results: The resins containing QAM showed antibacterial activity compared to the commercial material by immediately reducing the metabolic activity by about 60%. However, the antibacterial activity decreased after aging (p<0.05). None of the groups presented any differences for SBS (p>0.05) and DC (p>0.05). The incorporation of DMADDM and DMAHDM significantly reduced the keratinocyte viability compared to the GT and GC groups (p<0.05). Conclusion: Both adhesives with QAMs showed a significant reduction in bacterial metabolic activity, but this effect decreased after water aging. Lower cell viability was observed for the group with the longer alkyl chain-QAM, without significant differences for the bonding ability and degree of conversion. The addition of QAMs in adhesives may affect the keratinocytes viability, and the aging effects maybe decrease the bacterial activity of QAM-doped materials.

Resumo O objetivo do estudo foi determinar a influência do sistema fotoiniciador sobre as propriedades físico-químicas de compósitos fluidos. Os compósitos convencionais foram compostos por bisfenol-glicidil dimetacrilato (BisGMA) + trietilenoglicol dimetacrilato (TEGDMA), e os autoadesivos, apresentavam BisGMA +TEGDMA+ Bis2(metacriloiloxi)etil fosfato (2 MP). Cinco sistemas fotoiniciadores foram testados: canforquinona + etil-4- dimetilamino benzoato (CQ+EDMAB), óxido mono-alquil fosfínico (TPO) e óxido bis-alquil fosfínico (BAPO), CQ+EDMAB+TPO e CQ+EDMAB+BAPO. LED de amplo espectro foi usado; o grau de conversão (GC) e a taxa de polimerização (TP) foram determinados por espectroscopia próximo ao infravermelho; o grau de amarelo foi mensurado por um espectrofotômetro e absorção de água foi obtida após 30 dias de armazenamento em água (n=5). Os dados foram submetidos a análise de variância de dois fatores e teste de Tukey (?=0,05). BAPO apresentou os maiores valores de GC e TP nos compósitos convencionais e autoadesivos. Compósitos autoadesivos apresentaram menor GC e TP quando CQ+EDMAB foi usado. Maior amarelecimento foi observado nos compósitos autoadesivos em relação aos convencionais, exceto para BAPO. Compósitos autoadesivos promoveram maior absorção de água. Não houve influência dos fotoiniciadores nos compósitos convencionais, no entanto TPO e BAPO apresentaram os maiores valores de absorção de água nos compósitos autoadesivos. Os sistemas fotoiniciadores influenciaram de maneira diferente as propriedades físico-químicas dos compósitos convencionais e autoadesivos.

Abstract The aim of this study was to determine the influence of photoinitiator systems on physical-chemical properties of flowable composites. Conventional (CFC), composed by bisphenol-glycidyl dimethacrylate (BisGMA)+triethyleneglycol dimethacrylate (TEGDMA), and self-adhesive (SAFC), composed by BisGMA+TEDGMA+bis{2-(methacryloyloxy) ethyl} phosphate (2MP), flowable composites were developed. Five photoinitiator systems were tested: camphorquinone (CQ), ethyl-4-dimethylaminobenzoate (EDMAB), diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide (TPO), phenylbis (2,4,6-trimethylbenzoyl)phosphine oxide (BAPO), CQ+EDMAB+TPO and CQ+EDMAB+BAPO. A two-peak LED was used; degree of conversion (DC) and the maximum polymerization rate (RPmax) were determined by near infrared spectroscopy. For the yellowing degree a spectrophotometer was used. Water sorption (Wsp) was obtained after 30 days of water storage (n=5). Data were submitted to two-way analysis of variance and Tukey’s test (a=0.05). BAPO presented the highest DC and RPmax values for both series. SAFCs presented lower DC and RPmax for CQ+EDMAB-based materials. Greater yellowing was observed for SAFCs compared with CFCs, except for BAPO. Greater Wsp was observed for SAFCs compared with CFCs. The photoinitiator did not influence Wsp for CFCs, but TPO and BAPO presented the highest Wsp in SAFCs. The photoinitiator system affected differently the physical-chemical properties of CFCs and SAFCs.

There are few studies that fully characterize the effect of the filler size on the surface, optical and mechanical properties of resin composites. AIM: To determine the influence of the filler size content on surface, optical and mechanical properties before and after accelerated aging. METHODS: Seven resin composites were investigated: Filtek Supreme® (3M/ESPE), Estelite Σ Quick® (Tokuyama), Evolu-X® (Dentsply), Esthet-X HD® (Dentsply), Opallis® (FGM), Herculite XRV Ultra® (Kerr) and Filtek Z250® (3M/ESPE). Elastic modulus (EM) and flexural strength (FS) were determined by three-point bending of specimens immersed or not in absolute ethanol for seven days. Roughness (Ra) and gloss (G.U.) analyses were determined before and after ethanol storage for seven days and CIELAB color change (ΔE*) was obtained with a spectrophotometer. Results were analyzed by two-way ANOVA (general linear model) for EM and FS, with repeated measures for roughness and gloss, and one-way ANOVA for ΔE*. All comparisons were performed by Tukey's test (5%). Pearsons' correlation test was performed to determine the correlation between EM, FS, roughness, gloss, and ΔE* with the mean filler sizes. RESULTS: Mechanical properties decreased for all materials when submitted to immersion in ethanol. Increasing filler size gradually increased EM, FS and roughness values; gloss values decreased and didn't significantly affects ΔE*. Nanofiller composites presented higher gloss values than the others. CONCLUSIONS: It was possible to determine that the average filler size is a good predictor just for FS and gloss retention.