The present work concerns the preparation of bone cements based on poly(methyl methacrylate) (PMMA), used mainly for prosthesis fixation and cavity filling for correction of human bone failures. A typical bone cement recipe contains methyl methacrylate, which polymerizes in situ during cement application. An inherent problem of this reaction is the large amount of heat released during the cement preparation, which may lead to irreparable damage of living tissues. Optimization of PMMA-based bone cement recipes is thus an important step towards safe and reliable clinical usage of these materials. Important process variables related to the reaction temperature profile and the mixing of the recipe constituents were studied in order to allow for the adequate production of bone cements. It is shown that the average molar mass and size of the PMMA particles used in the production of the bone cement, as well as incorporation of radiopaque contrast, co-monomers and fillers into the bone recipe play fundamental roles in the course of the polymerization reaction. Furthermore, the injection vessel geometry may interfere dramatically with the temperature profile and the time for its occurrence. Finally, it has been observed that the morphology of the PMMA particles strongly affects the mixing of the bone cement components.

The main objective of the present work is to analyze the influence of some important operational reaction parameters (agitation speed, polybutadiene - PB - content and initiator concentration) on the final properties of High Impact Polystyrene (HIPS) produced in bulk. Variable effects are analyzed both qualitatively and quantitatively with the help of a fractional factorial design. Physical, chemical and mechanical properties were evaluated through measurement of the weight-average molecular weight (Mw), polydispersity (PD), volume-average diameter of PB particles (D(4,3)) and impact strength (Izod). It was found that PD and D(4,3) depend strongly on the initiator concentration, rubber concentration and agitation speed; Mw depends on initiator and rubber concentrations; and Izod depends on the rubber concentration, PD and D(4,3) in the analyzed experimental range. As a consequence, it was shown that control of final polymer properties can be easily performed through proper manipulation of the analyzed operational variables.

Artificial bone cements (BCs) based on poly(methyl methacrylate) (PMMA) powders and methyl methacrylate (MMA) liquid monomer also present in their formulation small amounts of other substances, including a chemical initiator compound and radiopaque agents. Because inadequate mixing of the recipe components during the manufacture of the bone cement may compromise the mechanical properties of the final pieces, new techniques to incorporate the fillers into the BC and their effect upon the mechanical properties of BC pieces were investigated in the present study. PMMA powder composites were produced in-situ in the reaction vessel by addition of X-ray contrasts to the reacting MMA mixture. It is shown that this can lead to much better mechanical properties of test pieces, when compared to standard bone cement formulations, because enhanced dispersion of the radiopaque agents can be achieved. Moreover, it is shown that the addition of hydroxyapatite (HA) and acrylic acid (AA) to the bone cement recipe can be beneficial for the mechanical performance of the final material. It is also shown that particle morphology can exert a tremendous effect upon the performance of test pieces, indicating that the suspension polymerization step should be carefully controlled when optimization of the bone cement formulation is desired.

The main objective of this work is analyzing whether it is possible to develop an empirical correlation for in-line estimation of the sulfur and nitrogen contents of the middle distillates Hydrotreating (HDT) products for control purposes. Correlations are based only on readily available in-line information of specific gravity variation between feedstock and products, without considering any piece of information about the kinetic behavior of the catalyst. Experimental data were obtained in pilot plants under operating conditions that are representative of refinery operations. Results indicate that the removal of nitrogen and sulfur compounds during middle distillates HDT can be monitored in-line in real time, based on the available measurements of specific gravity. This allows for development and implementation of advanced in-line procedures for monitoring and control of the HDT process in real time.

Este trabalho objetiva a modelagem das curvas de extração características do processo de extração supercrítica do óleo essencial de alecrim (Rosmarinus officinallis l.), obtidas nas isotermas de 310,15 e 320,15 K nas pressões de 100, 120, 140 e 160 bar, e interpretar os parâmetros e a função objetivo com conceitos estatísticos. Utilizou-se na resolução das equações do modelo o método das diferenças finitas, na obtenção dos parâmetros utilizou-se o método da máxima verossimilhança. Os resultados simulados indicam que o modelo utilizado constitui-se numa ferramenta capaz de representar as curvas de extração do processo de extração supercrítica.

This work intend to model supercritical fluid extraction of Rosemary essential oil (Rosmarinus officinallis l.) obtained at 310.15 and 320.15 K at 100, 120, 140 and 160 bar and to analyze the parameters and the objective function with statistic tools. We have been used the finite differences method to solve the model, the parameters were estimated using the maximum-likelihood method. The results have shown that the model can reproduce the experimental data of supercritical fluid extraction.

A trypanosome strain isolated from a sylvatic rodent (Echimys dasythrix) from Santa Catarina Island (Santa Catarina State, Brazil) was characterized by the following methods: experimental transmission and development in invertebrate hosts, morphometry, cross protection, complement sensitivity, lectin agglutination and isoenzyme profiles. Comparasions were made with standard Trypanosoma cruzi and T. rangeli strains. All methods except isoenzyne analysis led to the identification of the isolate as T. rangeli. The isoenzyme differences found could be explained on the basis of polymorphism. Therefore this is the first report of T. rangeli in southern Brazil, increasing the geographical distribution of this parasite.