The microstructure of a melt-spun Zr28Ni44Cu28 (at. %) alloy was characterized in order to determine the structures and compositions of the crystalline phases that compete with glass formation during rapid solidification. Two crystalline phases were identified, namely, a face centered cubic (FCC) zirconium oxide phase and a primitive cubic version of the big-cube oxide phase, using a combination of scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscopy techniques. Our results indicate that the Zr-O atomic pair interaction is preferential compared to the other atomic pair possibilities, supporting the formation of Zr-based oxides over the equilibrium phases in the ternary Zr-Ni-Cu system. Further, the results provide insight into the mechanisms of oxygen-induced crystallization in Zr-based BMGs and the corresponding decrease in glass forming ability (GFA) with increasing oxygen concentrations.

Abstract Zr-based bulk metallic glasses (BMGs) are widely used as mechanical components due to their excellent properties and high glass-forming ability. However, there is a lack of research concerning the tribological behavior of BMG versus BMG. The sliding characteristics of Vitreloy-105 (Zr52.2Cu17.9Ni14.6Al10Ti5 at.%) were studied in air using a pin-on-disk apparatus equipped for continuous measurement of friction force and without lubrication. The counterface material was the same BMG. The structure, thermal stability, and wear morphology were examined by X-ray diffraction, differential scanning calorimetry, non-contact profilometer, and scanning electron microscopy. For a normal load applied (10.0, 20.4 and 38.2 N) at constant 233 rpm the coefficient of friction ranged from 0.30 to 0.36 at steady state. Average wear rate was more pronounced on the pins under higher load and the predominant wear mechanism observed was adhesive, with presence of peeling-off and micro-cracks accompanied by some grooves and abrasive wear at lower loads.

Based on the Fe60Cr8Nb8B24 alloy, reported in the literature as good Glass Forming Ability (GFA), in this study the GFA of two new compositions was proposed, Fe68-xCrxNb8B24 (x=10,12). They were evaluated as good candidates to be new compositions of Bulk Metallic Glasses (BMG) with better corrosion resistance due to the high Cr content. Rapidly solidified glassy ribbons were processed, and based on their thermal characteristics, the critical thickness of the glassy structure formation (Zc) was estimated. The critical thickness (Zc) obtained experimentally using the wedge-shaped casting method was evaluated and it presented a much lower value than that estimated theoretically. However, the GFA of the compositions analyzed was ranked and this ranking (i.e. whichever has the most or least GFA) is in agreement with the result predicted theoretically. The GFA of Fe58Cr10Nb8B24, which presented a maximum thickness of the amorphous region of wedge-shaped samples of about 0.6 mm (but estimated it would be 3.56 mm), offered good prospects to be a new Fe-based glass former alloy which has better resistance to corrosion than the Fe60Cr8Nb8B24 alloy reported.

A good glass former, Ti57.4Cu33.4Ni9.2, was selected using the topological instability criterion (lambda criterion) and the average electronegativity approach. The crystallization behavior and microstructural development of amorphous melt-spun ribbons of this new composition in response to heat treatment were investigated using a combination of differential scanning calorimetry (DSC), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results indicate that the crystallization of the Ti57.4Cu33.4Ni9.2 alloy takes place through of three exothermic reactions with the nucleation of TiCu, Ti2Cu and Ti2Ni. The kinetics of crystallization were investigated by DSC, and the kinetic parameters were determined using Kissinger’s method.

A combination of an extension of the topological instability "λ criterion" and the "average electronegativity" has been recently reported in the literature to predict compositions with high glass-forming ability (GFA). In the present work, both criteria have been applied to select the Ni61.0Nb36.0B3 alloy with a high glass-forming ability. Ingots were prepared by arc-melting and were used to produce ribbons processed by the melt-spinning technique further characterized by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The Ni61.0Nb36.0B3 alloy revealed a complete amorphization and supercooled liquid region ΔTx = 68 K. In addition, wedge-shaped samples were prepared using copper mold casting in order to determine the critical thickness for amorphous formation. Scanning electron microscopy (SEM) revealed that fully amorphous samples could be obtained, reaching up to ~800 µm in thickness.