Abstract Over the last decades, alloy 718 usage has expanded and requirements imposed by its industrial applications became more critical. The knowledge about grain boundary character distribution (GBCD) in alloy 718 and its effect on properties improvement is mostly built based on iterative processing through cold rolling steps interspersed with solution annealing. Alloy 718 is found in the industry in many different forms and geometries, and fabricated by multiple thermomechanical processes such as wire drawing, rolling, forging or extrusion. The present study focused on understanding how wires respond to deformation mode related to drawing in regard to GBCD evolution, crystallographic orientation, precipitation of δ-phase and grain size. Lastly, assessing the resulting mechanical properties. The findings show that microstructural evolution is a consequence of competing mechanisms such as strain induced boundary migration, recrystallization, grain growth and phase precipitation. The deformation gradient along wire cross section plays an important role in affecting microstructural features, such as δ precipitation, GBCD and microtexture.

The development of β-metastable titanium alloys that combine low Young’s modulus, good mechanical properties, corrosion resistance and biocompatibility has attracted industry interest. This type of alloy is an alternative to commercial alloys such as Ti-6Al-4V, avoiding the cytotoxic effect that occurs with Al and V in the human body in the manufactured orthopedic prostheses. In this scenario, the present work aims to characterize the effect of Nb concentration in the properties of Ti alloys based on the Ti-12Mo-xNb stoichiometry (x = 0, 3, 8, 13, 17 and 20). All alloys were produced by arc melting with non-consumable tungsten electrode in an argon atmosphere and the ingots were characterized by x-ray diffraction (XRD), optical microscopy (OM), Vickers microhardness and Young’s modulus was measured by impulse excitation and density was measured using the Archimedes’ principle. The Ti-12Mo alloy and the Ti-12Mo-20Nb alloy showed the lowest Young’s modulus. The best hardness/modulus was found for the Ti-12Mo-3Nb alloy. All the alloys studied in this work showed hardness/modulus ratio above the traditional Ti-6Al- 4V alloy (2.85), presented great potential for the biomedical application.

2.25Cr-1Mo steels are widely used in thermoelectric power plants. Under operational temperatures, their properties degrade due to microstructural changes related to carbide coalescence and stoichiometric transformations. The extent of such microstructural changes is controlled by stress, temperature and time. Therefore, these factors can be used to evaluate damage and as life assessment tools for the individual component. In the past, ferrite-pearlite was the predominate microstructure in commercial Cr-Mo steel products, owing to the well-known methodologies for remaining life assessment based degradation. Currently, the ferrite-bainite microstructure obtained through a more economical route is most commonly used for this steel grade. However, there is no consensus in the literature about microstructural changes that can be used as a degradation pattern for ferrite-bainite steels. This paper compares the aged microstructures and creep properties of ferrite-pearlite and ferrite-bainite 2.25Cr-1Mo steels. Aging was conducted at 500, 575 and 600ºC until 2,000 h, and creep tests were performed at 575ºC under a stress of 100 MPa. Microstructural changes were characterized by optical microscopy scanning electron microscopy. Metallographic observations of the ferrite-bainite steel show a more stable behavior at the ageing temperatures and time considered. However, creep tests revealed that the ferrite-pearlite microstructure possesses a better rupture time performance. Carbide size distribution and stoichiometric evolution of the carbides provided by transmission electron microscopy support the creep behavior. These results show that the current techniques for evaluating microstructural degradation of 2.25Cr-1Mo steels must be reconsidered.

Metastable β-type Ti alloys with non-toxic addition elements such as Mo, Zr, Sn, Ta and Nb were developed as an alternative to the widely used Ti-6Al-4V alloy for biomedical applications. These alloys possess enhanced biocompatibility and reduced elastic modulus in comparison with Ti-6Al-4V. Moreover, for orthopedic implants, low Young's modulus is required in order to avoid the stress shielding phenomenon. This study analyzes the microstructure and mechanical properties of a new Ti-12Mo-8Nb alloy after hot swaging, annealing at 950 ºC for 1h and water quenching. The alloy was characterized by X-ray diffraction, optical microscopy and transmission electron microscopy. Tensile tests were performed at room temperature. Young's modulus and hardness values were also measured. The structural characterization reveals a metastable β structure containing only a small amount of α and ω phases. Exhibiting a lower Young's modulus than Ti-6Al-4V and other previously studied Ti-Mo-Nb alloys, the Ti-12Mo-8Nb alloy can be a promising alternative for orthopedic application.

Two distinct AISI type 316 stainless steels, of Brazilian and Swedish origins, were compared regarding their creep fracture mechanisms at 600, 700 and 800°C. The possible mechanisms associated with the creep fracture strength were identified by means of fracture maps proposed either by Ashby and collaborators or by Miller and Langdon. Experimental creep results were consistent with the general Ashby and collaborators map for face centered cubic alloys. By contrast, the two different 316 steel displayed significant differences in the model-based map of Miller and Langdon. In the present work, changes in the maps frontier are proposed as well as the introduction of a new field in the map related to grain boundary precipitation. These propositions allowed the Miller and Langdon map to be coherent with the experimental creep fracture results of both 316 stainless steels.

β-metastable titanium alloys with high strength to Young’s modulus ratio have been developed by different authors aiming their use as biomaterials for hard tissue replacement. However, it is not easy to combine low elastic modulus with high mechanical strength. In this work, a β-Ti alloy (Ti-10Mo-20Nb) was produced by arc-melting, then homogenized, cold swaged and aged in order to obtain fine α-Ti precipitates in a β-Ti matrix. The microstructures were characterized by transmission electron microscopy and X-ray diffraction. Mechanical properties characterization was based on Vickers microhardness tests and Young’s modulus measurements. The cold swaged material subjected to an ageing treatment at 500 °C for 4 h showed the highest hardness/ Young’s modulus ratio, associated to very fine α phase precipitates in a β-Ti matrix.

Beta titanium alloys were developed for biomedical applications due to the combination of its mechanical properties including low elasticity modulus, high strength, fatigue resistance, good ductility and with excellent corrosion resistance. With this perspective a metastable beta titanium alloy Ti-12Mo-13Nb was developed with the replacement of both vanadium and aluminum from the traditional alloy Ti-6Al-4V. This paper presents the microstructure, mechanical properties of the Ti-12Mo-13Nb hot swaged and aged at 500 °C for 24 h under high vacuum and then water quenched. The alloy structure was characterized by X-ray diffraction and transmission electron microscopy. Tensile tests were carried out at room temperature. The results show a microstructure consisting of a fine dispersed α phase in a β matrix and good mechanical properties including low elastic modulus. The results indicate that Ti-12Mo-13Nb alloy can be a promising alternative for biomedical application.