Objetivou-se com este trabalho avaliar a distribuição de líquido da ponta de pulverização com indução de ar e jato excêntrico AIUB 8502 sob diferentes condições operacionais. Foram avaliados perfil individual, vazão, ângulo de abertura do jato, faixa de aplicação e distribuição volumétrica simulada de duas pontas AIUB 8502 nas pressões de trabalho de 200, 300, 400 e 500 kPa, altura de 30, 40 e 50 cm em relação ao alvo e espaçamento entre pontas de 30 a 100 cm. Todas as análises foram realizadas seguindo a norma ISSO 5682-1, com algumas adaptações. A ponta apresentou distribuição de líquido excêntrica com um lado descontínuo e extremidade oposta excêntrica, com queda abrupta do volume de líquido. À medida que se aumentou a altura da barra e a pressão de trabalho, alongou-se o perfil do jato. O maior número de configurações uniformes foi obtido na altura de 50 cm, decrescendo nas alturas de 40 e 30 cm. A vazão e o ângulo do jato excêntrico aumentaram com o incremento na pressão, não havendo diferença entre o ângulo do jato descontínuo e o total entre as pressões de 400 e 500 kPa e de 200 e 300 kPa.

The objective of this work was to evaluate the liquid distribution of air induction and off-center AIUB 8502 spray nozzles under different operating conditions. Individual profile, spray nozzle outflow, spray angle, spray width and simulated distribution profile for two AIUB 8502 nozzles at working pressures of 200, 300, 400 and 500 kPa, height of 30, 40 and 50 cm from the target and 30 to 100 cm spacing were evaluated. All the tests were performed following ISO 5682-1 with some adaptations. The nozzles presented an eccentric liquid distribution with a discontinuous side and eccentric opposing end, with sharp decrease in volume. Profile distribution increased with increased bar height and working pressure. The largest number of uniform configurations was obtained at the height of 50 cm, decreasing at the heights of 40 and 30 cm. Angle and flow rate of the off-center nozzle increased with increase in pressure, with no differences between discontinuous and total angles between 400 and 500 kPa, and 200 and 300 kPa pressure ranges.

The objective of this work was evaluate the transversal spray deposition of double plain spurt nozzles TTJ60-11004 and TTJ60-11002 in different operational conditions. Was used five samples of each nozzle and considerate a unite one repetition. The spray deposition was evaluate on a table of evaluation distribution constructed in accordance with norm ISO 5682-1. Was evaluate a single spray distribution, volumetric distribution of the overlapping spurts by means of the coefficient of variation (CV%), outflow and angle of opening of the spurts. The operational conditions had been pressure of work of 200, 300 and 400 kPa, height of 30, 40 and 50 cm in relation to the target and spacing between nozzles in 45 and 100 cm simulated in software (Microsoft Excel). The nozzles presented discontinous individual profile with higher liquid deposition in the central region and gradual volume reduction in direction to extremities. The increase in the pressure promoted along of the profile and the band of application. The nozzles provided profile uniform to depend on the space between nozzles, with lesser values with reduction in the space and higher pressures. The outflow and the angle of the spurt had increased with the increment in the pressure

El objetivo de este trabajo fue el de evaluar la deposición transversal de caldo de las boquillas pulverizadoras de doble abanico TTJ60-11004 y TTJ60-11002 en distintas condiciones operacionales. Se utilizaron 5 muestras de cada boquilla pulverizadora siendo considerada cada unidad, una repetición. La distribución de caldo fue evaluada por medio de una mesa de evaluación de distribución construida de acuerdo con la norma ISO 56821. Se evaluó el perfil de distribución individual, la distribución volumétrica simulada de la superposición de los chorros por medio del coeficiente de variación (CV%) de los volúmenes colectados, el caudal y el ángulo de abertura de los chorros. Las condiciones operacionales fueron: presión de trabajo de 200, 300 y 400 Kpa, altura de 30, 40 y 50 cm en relación al blanco y espaciamiento entre boquillas simulados en Software (Microsoft Excel) entre 45 y 100 cm. Las boquillas presentaron perfil individual descontinuo con la mayor deposición de líquido en la región central y reducción del volumen gradual en dirección a las extremidades. El aumento de la presión promovió alargamiento del perfil y de la franja de aplicación. Las boquillas proporcionaron perfil uniforme que dependió del espaciamiento entre las boquillas, con valores menores con reducción en el espaciamiento y en presiones mayores. El caudal y el ángulo del chorro aumentaron con el incremento en la presión.