This work developed ternary films based on Poly(Lactic Acid) (PLA), Cloisite 30B (C30B) and Oregano Essential Oil (OEO) as proposal to be applied in food packaging. The films thus manufactured were unscathed, with reduced surface defects. Their thickness and moisture content varied according to the composition and content of each component in the formulation. Optical micrographs indicated a homogeneous morphology, with good distribution of clay in the matrix. FTIR data confirms the incorporation of OEO into the films. TGA analysis indicated that the thermal stability of the films was not significantly affected by the incorporation of C30B and OEO. OEO incorporation did not promote an efficient antimicrobial action which is probably due to its retention by the clay. Further studies are needed to confirm this hypothesis. The combination between C30B and OEO in the PLA polymeric matrix is a promising proposal.

Abstract The use of polymer blends and composites based on fossil-based and bio-based polymers has become an important environmentally protective alternative for common use and disposable plastics applications such as packaging, bottles and trays. The disposal of these more degradable products, however, may also harm the environment and, therefore, recycling these systems becomes relevant. Recycling involves reprocessing which can significantly change the morphology and properties of polymeric products. Therefore, this study deals with the effects of reprocessing cycles on the properties and morphology of blends and nanocomposites based on fossil and bio-based polymers. The systems investigated were: a) neat polypropylene (PP), b) a polypropylene/poly(3-hydroxybutyrate) (PP/PHB) blend and c) PP/PHB/organoclay nanocomposite compatibilized with polypropylene-g-maleic anhydride (PP-g-MA) and erucamide. These materials were submitted to up to seven extrusion cycles in a single screw extruder operating at 60 rpm. Samples were taken after the first, third, fifth and seventh extrusion cycles and their tensile properties and morphology were determined. Scanning electron microscopy indicated that two phases were observed in the blend which showed spherical PHB domains. The addition of clay, PP-g-MA and erucamide improved the adhesion between the nanocomposites components. X-ray diffraction analysis showed that crystallinity tended to increase with the number of reprocessing cycles for all systems investigated up to the fifth cycle and then tended to decrease. A 10% crystallinity increase was observed for neat PP in the fifth cycle. In general, the tensile properties of all systems decreased with reprocessing and the highest losses were observed for the PP/PHB blend after seven processing cycles with 50% and 37% decreases in stress at break and elastic modulus, respectively. Impact strength of the PP matrix and of the PP/PHB blend tended to decrease with reprocessing, except for the nanocomposite which showed a slight increase especially after the seventh processing cycle in which an 18% increase in impact strength was observed.

Polymeric syntactic foams are composites made from the mixture of Hollow Glass Microspheres (HGM) and polymer matrices. One of their main characteristics is their low density and the production of these composites using a matrix derived from renewable sources potentiates their development without neglecting sustainability. In this paper , the properties of High Density Polyethylene (HDPE)/HGM syntactic foams containing 1% and 5% w/w HGM and 5% w/w of a compatibilizer are assessed. The composites were prepared by two processing routes: single screw extruder and twin screw extruder. The morphology and mechanical properties (tensile and impact) of the syntactic foams thus manufactured were ascertained. Morphological analysis indicated that matrix/filler adhesion was poor for all samples and that the best HGM dispersions were obtained in twin screw extruded samples. Mechanical properties were affected by the processing route adopted and by the content of hollow glass microspheres added. Elastic modulus, tensile strength and strain were reduced by 20, 10 and 23%, respectively, in systems processed in a twin screw extruder. Impact strength was the exception, with an increase of more than 300%. Higher contents of hollow glass microspheres led to reductions in mechanical strength of the syntactic foams, varying from 5% for the elastic modulus to 50% for strain.

RESUMO O Polietileno (PE) Verde é um polímero sintético que apresenta baixa energia superficial, que resulta em fraca propriedade de adesão. Esta baixa adesão, provoca alguns problemas relativos às aplicações práticas dos polímeros, como fraca aderência de tintas de impressão, revestimentos, adesivos e metais à superfície do polímero, entre outros. Uma maneira de alterar essa propriedade é por meio da aplicação de um tratamento por plasma. Neste sentido, o objetivo deste trabalho foi preparar, via extrusão plana, filmes de biocompósitos com matriz de PE Verde (PEPURO) e carga de argila Vermiculita Expandida (VMT) no teor de 1%. Os filmes foram tratados por plasma em duas condições distintas: sob atmosfera de Oxigênio (O2) (C1); e sob atmosfera correspondendo a mistura de Argônio/Hidrogênio (Ar/H2) e um posterior tratamento por plasma sob atmosfera de O2 (C2). Os resultados indicaram que os tratamentos a plasma e a incorporação de VMT aumentaram a hidrofilicidade dos filmes, sendo que a aplicação da condição 2 (C2) mostrou-se de maneira mais eficiente. O PEPURO não tratado apresentou redução significativa de resistência máxima a tração com a inserção de VMT, já com a aplicação dos tratamentos (C1 e C2) os valores de resistência foram superiores. Em relação à rugosidade foi possível verificar que a aplicação do plasma aumentou a rugosidade na superfície das amostras. Estes resultados indicaram que o aumento da hidrofilicidade e da rugosidade resultaram em um aumento significativo na interação de fluidos com a superfície e também melhora das características adesivas do polímero.

ABSTRACT Green Polyethylene (PE) is a synthetic polymer that has low surface energy, which results in poor adhesion properties. This factor causes some problems regarding the practical applications of polymers, such as poor adherence of printing inks, coatings, adhesives and metals to the surface of the polymer, among others. One way to alter this property is by applying a plasma treatment. In this sense, the objective of this work was to prepare, by flat extrusion, biocomposite films with Green PE matrix (PEPURO) and load of Expanded Vermiculite Clay (VMT) in the 1% content. The films were treated by plasma under two different conditions: under O2 atmosphere (C1); (Ar/H2) and a subsequent treatment by plasma under O2 (C2) atmosphere. The results indicated that the plasma treatments and the incorporation of VMT increased the hydrophilicity of the films, and the application of condition 2 (C2) was shown more efficiently. The untreated PEPURO presented a significant reduction of maximum tensile strength with the insertion of VMT, already with the application of treatments (C1 and C2) the resistance values were higher. In relation to the roughness it was possible to verify that the application of the plasma increased the surface roughness of the samples. These results indicated that increased hydrophilicity and roughness resulted in a significant increase in the interaction of fluids with the surface and also improvement of the adhesive characteristics of the polymer.

Polyethylene (PE) is a polymer that has a low adhesion property, which is related to its low surface energy. However, the plasma treatment aims the modification of the surface properties without affecting the polymer structure. In this sense, the objective of this work was to prepare biocomposite films via flat extrusion with Green PE matrix and Expanded Vermiculite Clay (VMT), contents of 1, 3 and 6%. The films were treated by plasma in two different ways: Oxygen (O2) atmosphere (Condition 1); and Argon/Hydrogen (Ar/H2) atmosphere followed by a plasma treatment under O2 atmosphere (Condition 2). The results of the contact angle measurements indicated that the incorporation of VMT and the conditions used for plasma treatment increased the films wettability due to the hydrophilic character of VMT and also as a consequence of the plasma. In contrast, the XRD diffractograms indicated that there were no significant changes in the films structure.