The depletion of conventional energy sources and the concern with the environmental impacts of the use of fossil fuels sparked interest in researching new energy sources and improving existing processes. In this context, the solar energy presents itself as one of the most promising energy sources on the planet, given its wide availability and applicability in thermal processes. However, its use still represents a great technological and economic challenge, because many systems that use this energy still have low efficiency and high cost, which makes them uncompetitive in competition with systems using other energies. With that, the search for the improvement of the processes awakens the researches in more adequate and cheaper materials, which represents a great scientific potential in the evolution of these technologies. Thus, the present work proposes to obtain and analyze a selective surface for applications in solar-thermal collectors, using CRFO (compound formed by chromium and iron oxides), varying the percentage by weight, and then mixed with aluminum oxide. For the tests, an experimental bench was built to simulate a flat plate solar-thermal collector in real operating conditions. Some characterizations were carried out, such as: techniques scanning electron microscopy (SEM), infrared analysis and UV-VIS absorptivity determination, as well as the graphs with surface temperatures and with radiation during the tests in the Sun for the composite (CRFO and aluminum oxide) and for the commercial surface (MRTiNOX). With the results obtained, it was verified in the field test that one of the produced selective surfaces obtained a result of absorptivity of 0.94 and 0.0349 of emissivity, which is close to that of the commercial surface. The results were confirmed in the characterization by UV-VIS, which showed high absorptivity values in the visible light range.

Abstract Founding new materials and structures for solar cells is a challenge in the photovoltaic field. This work evaluated the effect of the lignin in the photovoltaic activity by compounding with TiO2/lignin as photoanode for the dye sensitized solar cells (DSSC’s). Hybrid films (TiO2/lignin) with different concentrations of lignin (5, 10 and 15%) were deposited by spin coating over commercial TiO2 thin films. The cells were sandwich assembled. The characterizations were done through analysis of absorbance, band gap, x-ray diffraction, morphological and electrical. The lignin at 15% reduced the TiO2 band gap from 3.66 to 2.84 eV, favoring the short current density to 11.06 mA/cm2 and efficiency of 4.65%, an increase of 103.95% compared to the TiO2 structure without lignin.

This paper presents the study of the addition of the polyaniline polymer (PANI), at the junction of the cadmium telluride and cadmium sulfide (CdTe/CdS) layers in order to improve the contact between the layers, to decrease the air gap that limit the conversion photovoltaic. The morphology of CdS, CdTe and polyaniline (PANI) were characterized with multiple techniques including scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and optical absorption. The Metrohm Autolab LED Driver Kit system was used for data collection, and it was possible to obtain the current and voltage parameters of the cells. The inclusion of PANI thin film in CdS/CdTe hybrid solar cells increases the energy conversion efficiency from 0.0075% to 0.15%, this gives a 20-fold increase in efficiency.

Abstract A low cost spin coater was constructed in this work for the deposition of thin films of titanium dioxide (TiO2) on conductive substrate of FTO (fluoride doped tin oxide) with application on dye sensitized solar cells. The results showed a 95% precision between the speed values obtained by the software of C#sharp language and the spin values observed directly on the device. The TiO2 films deposited through the spin coater with different angular speeds were characterized by UV-Vis optical spectrum, scanning electron microscopy (SEM), atomic force microscopy (AFM) and electrical measurements on an active area of 0.25 cm2. The DSSCs assembled with the TiO2 films of double layer deposited by the spin coater had an efficiency value of 12.74%, while the cell with a single layer presented 4.05% efficiency. Therefore, it is concluded that the spin coater assembled in this study at low costs successfully can produce TiO2 electrodes for DSSCs.

ABSTRACT The depletion of fossil fuel reserves and climate change caused by atmospheric pollution has led the human being to seek alternatives that are less damaging to the environment. The concern and the awareness of the population open space for the study of renewable energies to be deepened, among them the best use of solar energy. The use of alternative materials to replace selective surfaces is a natural trend, since improvements in surface efficiency are usually sought while attempting to reduce costs. Composite substances are already used to obtain some selective surfaces, and, as a result, the search for better processes awakens research on more appropriate and lower cost materials, which represents a great scientific potential in the evolution of these technologies. Thus, the present work consisted in obtaining and studying selective surfaces for applications in low-cost flat plate solar collectors, using residues from the granite industry. Five different surfaces were studied, varying the weight percentage: 100% granite powder, 75% granite powder + 25% chromium oxide, 50% granite powder + 50% chromium oxide, 25% granite powder + 75% chromium oxide and 100% chromium oxide. For the tests, an experimental wooden stand was built, and it was possible to simulate the conditions of a flat plate solar collector. To characterize the surfaces, scanning electron microscope (SEM) techniques, infrared analysis, X-ray diffraction and UV-VIS absorbance determination, as well as graphs with surface temperatures and with radiation, during the tests in the sun, were used. The surfaces` efficiency was determined by the ratio of the absorptivity by the emissivity, as well as the trademark MRTiNOX, a commercial selective surface applied on copper substrate. For this, an efficiency of 23.56 was obtained, while for the 50% granite and 50% chromium surfaces the value of 23.27 (closest to the trade mark) was calculated. Therefore, replacing the traditional components of selective surfaces with granite proved to be a satisfactory solution, contributing to the reduction of costs with work involving solar energy.